453960-1-S-Frigidaire-5303051519        -Bake Element - 240V
453960-1-S-Frigidaire-5303051519        -Bake Element - 240V 453960-2-S-Frigidaire-5303051519        -Bake Element - 240V http://www.partselect.com/Schematics/Frigidaire/Frigidaire_Thumb/U9WBWEYQ.gif

Bake Element - 240V

PartSelect Number PS453960

This heating element is a partially open-style bake element. Carrying 240V and 2000W, it is 19-1/4" wide by 15" long. The two 90-degree push-on male spade terminals are 13-3/4" apart.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Oven is too hot.
  • Will Not Start.
  • Compare At

    $20.66
  • You Save

    $3.44
  • Your Price

    $17.22
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 107 reviews What's this?
1-5 of 107
 

119 of 125 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerChristopher from North Salt Lake, UT

Baking heating element burned up

Used a screw driver with a socket head to remove the two hex head screws holding the old element. Pulled the old element forward until the two wire attachements were visable. The wires were attached with a simple tab connector. Removed the wires from the element. Attached wires to new element slide the element and wires back into wall of oven and replaced screws. Done!

Help other customers find the most helpful instructions.

Were these instructions helpful?

35 of 37 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

Customerjoseph from washington, PA

Blown bake element

Removed the two screws that hold the element in place at the rear of the oven.Unplug each prob,you may need pliers as they can be a little tight.Reconnected the new element.Keep the old screws.New element does not come with screws.Always unplug range when doing repairs.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 22 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerDennis from Flatwoods, KY

Element went out in 20+ year old oven

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the element and put back in place. Took about 10 minutes. Repair part came in 2 days. Very awesome website!

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 10 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerMatthew from Beverly Hills, FL

Oven wouldnt heat

I assumed the bake element was the problem,so I ordered one from Part Select.I was amazed that I got it in 2 days! After removing the 2 screws that held the element in place,I disconnected the 2 wires from the element.I wasnt being very careful and let one of the wires slip back into the hole in the back of the oven.Couldnt get the wire back out,so I had to take the back of the stove off to get to it.Next time,I'll be careful to keep the wires from going back into the holes.Then I connected the element,screwed it in place an turned the oven on.Success !!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 12 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerJule from New Salem, PA

Old element visibly burned out

Unplugged oven, unscrewed element, removed back pannel, unclamped old element and removed it, installed new element, clamped it to wires, screwed element to inside of oven, then replaced back pannel
Whole thing took about five minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 107