Quick Question!

Have you ever purchased from PartSelect.com before?

453960-1-S-Frigidaire-5303051519        -Bake Element - 240V
453960-1-S-Frigidaire-5303051519        -Bake Element - 240V 453960-2-S-Frigidaire-5303051519        -Bake Element - 240V http://www.partselect.com/Schematics/Frigidaire/U9WBWEYQ.gif

Bake Element - 240V

PartSelect Number PS453960

This heating element, used in any range/oven, is an open-style bake element. It is placed at the bottom of the oven and supplies heat. If your baking element does not supply consistent heat or is burnt out, then replacing the element is the solution to this problem. This heating element is a 19-1/4 inches wide by 15 inches long. The push-on male spade terminals are 13-3/4 inches apart. The tools needed for this replacement are: a screwdriver and needle-nose pliers. The first step in is to unplug the range or shut off the house circuit breaker before starting. Unscrew the back of the oven cavity to pull out wires from the defective element. Reconnect wires to the new element and screw it back.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Oven is too hot.
  • Will Not Start.

Compare At

$21.07

You Save

$3.51

Your Price

$17.56
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 108 reviews What's this?
106-108 of 108
 

0 of 2 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Steve from Sarasota, FL

The old element disintegrated into little pieces

Please make sure the oven is off before working on oven.
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: stephen from york, PA

Burnt out

removed 2 screws , pull element forward , disconnected connector . pushed connectors on
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Bake Element - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Socket set
Customer: Barney from Naylor, MO

Lower heating element burned out

i removed the 2 screws that held the elrment in place. then pulled the element out about 3 inches and disconnected the two wires , reconenected the 2 wires to the new element and pushed it back in and replaced the 2 screws. the only part available locally was through a service man who would not sell it without installing it. at twice the price plus a service call.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

106-108 of 108