Heater Coil with 5/16" Terminals

PartSelect Number PS451032

Coil only.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Compare At

    $56.18
  • You Save

    $9.36
  • Your Price

    $46.82
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.0 / 5.0, 3 reviews What's this?
1-3 of 3
 

45 of 56 people found this instruction helpful

Parts Used

  • Heater Coil with 5/16" Terminals

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerMark from Normalville PA

Dryer would not heat

First..kudos to PartSelect for their fantastic support! Great work folks.

While greasing the bearing in the back of the drum, I found my heating coil was broken. Steps to replace:

1) Unplug the unit
2) Remove the top panel. Note, do not remove the center front screw that does not go into the door.
3) Remove front outer panel
4) Remove interior front panel
5) Remove front control panel 6 screws, pushing downward the panel and disconnecting connection to door.
6) Remove door by removing the screws on the top and pull door straight off. (I left the air duct attached to the door)
7) Remove the back access panel to the motor
8) Release the belt from the idler pulley and remove the belt.
9) I removed the three screws in the center of the drum as I found it difficult to remove the drum from the bearing. Remove the drum.
10) disconnect the coil terminals by first bending the tabs outward to allow you to be able to pull them off the block
11) remove the old coil
12) carefully stretch the new coil so that it measures 48 inches (no more)
13) Plug new coil into terminals and bend tabs to lock in place.
14) Divide heater coil in half and install coil onto center support on the opposite side from where it connects to the block/back wall of dryer
15) Install remaining coils onto supports.
16) reinstall all parts in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 15 people found this instruction helpful

Parts Used

  • Heater Coil with 5/16" Terminals

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Wrench(Adjustable)

CustomerC. William from Milford NY

No heat from dryer

Repair requires nearly complete dis-assembly of the cabinet.Starting with the steel panel directly below the control panel, remove 2 screws. Next, remove the screws on the lower corners of the control panel. The control panel can drop down now and be removed from the cabinet. The door frame must be removed next. Start by disconnecting the door interlock connector from the wiring harness and then removing the screws on the top of the cabinet that hold the frame. remove the frame. The dryer tub is next and is removed by extracting the three screws in the back of the tub that bolt it to the bearing. The tub is now free and is pulled out of the front of the cabinet. Now comes the challenging part. The actual bearing is a sphere that is held in place by a spring loaded socket. The bearing must be removed in order to access and heater assembly. The bearing is removed by pushing it with considerable force upward toward the top of the cabinet. This strong force is necessary in order to overcome the force of the springs that hold the ball bearing in in place. I found removal of this bearing perplexing because no mention is mentioned anywhere of the amount of upward force that it takes to remove it and I was afraid of breaking it by forcing it. Now the heater assembly can be easily removed and replaced. This whole process is challenging and time consuming. At the same time you can feel a degree of satisfaction when you are done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 13 people found this instruction helpful

Parts Used

  • Heater Coil with 5/16" Terminals

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerReed from Seatac WA

Drum turns but no heat

Frigidaire / electrolux stack washer dryer
Removed door panel,top,control panel not sure all needed to be removed except door then removed 3 screws in center at rear of drum this disconnects the drum to shaft that secures it in place ( could not find info on that step and is the reason for writing this hope it helps , reassemble in reverse

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3