Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS434226
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
Repair is simple and straight forward. Simply open oven door and remove oven racks. A philips #2 screwdriver is needed to remove 2 screws, 1 on each side at lower portion back of of oven..Slowly pull heating element out towards front of oven, wires will pull out with it. Simply wiggle and unplug spade connectors on each side, plug new ends of heating element into wires. Slide heating element back in re-attach removed screws not over tightening just till snug.Front drawer glides: Remove oven drawer and this is a good time to give it a good solid cleaning. Clorox wipes and elbow grease. The handle can be removed to clean under neath as well just a few screws to remove with the same philips screw driver.The front drawer glides do not mount on the drawer, they mount on each lower side of drawer opening above lower glides. There is a squared off small opening on each side for the glides to pop into with small square notches at the bottom of each hole.Take the curved part of the glide and angle the insertion going into the hole turning down and pushing in, the glide will "Pop" or "Click" when seated. That's it. Save time and money and fix it your self. You don't need to buy a new range when parts and do it your self are less than $30.00.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Read the instructions provided and simply installed the guides. Total time was less than 5 min.
the part snapped on the side of the track, now the draw is not sitting on the floor and opens and closes like new.
After researching on what exactly to call the part, which was a front drawer glide. I found this out by watching the video. It showed me exactly what I needed and what it looked like. I run to the oven to look at the other one, to make sure thats what I needed, and it looked like the part that I needed (mind you I am a female, and not a repair person), so this video helped me out alot. When the part arrived, I knew how to take the drawer out, and easily snapped the little plastic glide in to place, and slipped the drawer back on the gliders, and it worked perfect, so proud of myself, that I done it by myself, with no help from husband. I bragged and bragged on myself with a big pat on my own back, thanks Part Select, I know what to do when it happens again. Its my fault cause it broke, cause I overload the drawer with pots and pans LOL!!! Brenda Dixon
Just use flat screwdriver to press on clip and just squeeze it in
I removed the drawer, removed and replaced the guides on both sides in the front and replaced the drawer.
Removed the drawer. Inserted the new glide tab into a hole in the side. Inserted the drawer slides in the the glide. Closed drawer--done! Works fine. Probably only 5-10 minutes.
The on-line video made it real easy.
I attached the drawer glide clips to the stove and inserted the drawer, done in minutes. The video on your site actually made it very easy made it so there was no guessing.
So easy! The drawer glides just popped right in!
Popped out the old ones with a screw driver. Pushed in the new ones. Whole process took less than three minutes, super easy.
snapped new glide in place.
Found correct parts on Partselect.com, watched the instructional video, ordered the parts and installed them when they arrived. Very simple, very easy.
I pul;led out the drawer and inserted the front glide in about 2 seconds and slid the drawer back in! Presto--fixed!
Removed drawer and replaced broken and missing parts. Very easy when you have correct parts.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.