Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS430126
As you look into the fridge, this drawer support track is located on the right hand side.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
This screw is sold individually.
This drawer rail supports the left hand side of the sliding drawer. The mounting screws are sold separately.
first I emptied the old draw, then I pulled it out . Next i removed old draw support and replaced with new one. I then slid in new draw and refilled it
Help other customers find the most helpful instructions.
Were these instructions helpful?
Followed the video instructions and it works like a charm! To top it off, the part got to my house the day after I ordered it! Fantastic service!
1) Viewed the video 2) Got a screw driver 3) Removed the shelf/bracket assembly 4) Removed the old support 5) Reassembled and put back in place. It took longer to clean the dirty shelf than to fix the support. Very easy.
I just watched the online video and then did.
My grandson took the old side arms off and replaced it with the new. Everything was so easy and quick. Thank you so much. Joyce
I took out the drawer, then the whole shelf. I unscrewed the track that was broken and screwed in the new one. I then, put the shelf back in the fridge and put in the new drawer. All works awesome!!!Thanks PartSelect for getting me the parts I needed so fast!
Remove everything from shelf drawer is under. Remove everything in drawer. Remove the drawer itself. Remove the shelf the drawer slides underneath of by lifting front of shelf until legs unhook, then wiggle or gently pull until it releases from pieces legs hook into (each leg has one hook). Shelf should pull out with rails and legs attached. Remove screw with philips head screwdriver. I used a Stanley brand nut driver with philips and flathead bits included, $5 at Wal-Mart. Remove the screw holding the rail and leg together. Remove rail and replace with like part. Install screw. Hang shelf. Install drawer. Put all yer stuff back on shelf and in drawer. $50 cause step-son's kids like to pull out drawer and hang on it, go figure. Very simple fix. Do not lose screw! I put all my parts (drawer, shelf, rails, screw) on my kitchen counter. Mate your rail by aligning flat side of rail to inside flat surface of leg. Takes about five minutes. I would say good luck but you will not need it. Thank you PartsSelect for having such a user-friendly website!
pulled the draw out ,then unloaded shelf,removed shelf and unscrewed rails. I slid the rails of and put the new ones on screwed them back on and reassembled the drawer and shelf
It was just a matter of taking out 1 screw that held the old support, replacing the drawer support with the new piece and replacing the screw that held it on.
Removed the meat drawer from shelf. Removed shelf from fridge. There is one Phillips-head screw holding each support rail in place. Remove screw, and then each rail can be removed. Place each new rail in place, and then replace screw. Put shelf back in fridge and replace meat drawer. Total time -- about 5 minutes!The most difficult thing was ordering the parts. The right rail is called "Drawer Support Rail - right side". Fairly self-explainatory. The left rail is called "Track". Fairly confusing. Luckily, PartSelect.com has very good photos of the parts that they sell, and one can figure it out. It would have been much easier if both left and right rails were named similarly.
Removed the one screw holding the rail, positioned the new rail and put the screw back in.This was the best company I ever dealt with - the part arrived in less than 24 hours. Incredibly fast,and the order was right the first time.
Right broken rail was one screw. Both rail and deli drawer fit like a glove. Transferred groceries and was done.
Dropped it in!! A two minute fix. No problem.
Had to replace both sides tracks; the plastic is thin and gets alot of use. Had these done in minutes, one screw out on each side allows the tracks to be removed.Best part of the repair is the new clean shelves and drawers. How can you do this repair without cleaning everything? Nice quick service from PartSelect, and the right parts!
One screw to remove the old part, and screwed in the new one. Easy as pie. Keep the screw from the old part as the new one did not have one.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.