Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS429803
Sold individually. Also known as a short door closing cam.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
Sold individually. This cam is located at the bottom of the fridge/freezer door.
Before removing door, remove everything from on the door including the shelves, then close the door. Using a step ladder to access the top of the door, I removed the plastic hinge cover at the top of the refrigerator door using a Philips head screwdriver, remove the screw located at the back of the cover and slide the cover forward and up to remove. This will expose the two 3/8 machine screws that hold the top hinge bracket. Remove the screws using a socket or wrench. Then lift up on the hinge bracket from the top of the door to remove it. As long as the door is closed it will remain stable with little pressure to keep from falling. Then lift the entire door from the bottom hinge assembly and lay it across an arm chair or flat elevated surface so you can access the bottom door hinge bearing. You will see a bracket screwed to the bottom of the door with two 1/4 machine screws, it is the door stop bracket and this has the door hinge bearing inserted through it. My bearing was broke in half , the first piece fell out when I removed the door and the other piece was still inserted in the door. I removed one 1/4 screw from the stop bracket and loosened the other screw to allow the bracket to swing away from cavity that holds the bearing. Using needle nose pliers I remover the broken piece of the bearing. This part is nylon or plastic and can be cut into pieces if need be to remove it. Once removed, I cleaned the cavity, reinstalled the stop bracket assembly then inserted the new bearing. Gently align the door to the bottom bracket and set it in place, a second set of eyes may help. Once the door has been seated and in the closed position replace door bracket and the two 3/8 screws at the top of the door, check the alignment before you tighten. Check door operation! Then tighten the screws and replace the plastic cover by pressing down on the cover and sliding it back to align the Philips screw to be replaced .
Help other customers find the most helpful instructions.
Were these instructions helpful?
I emptied the door of food, removed the top hinge by removing two screws. I then lifted the door off the lower hinge. The teflon hinge was just sitting in the bottom bearing. I removed the broken one and replaced it with the new bearing hinge. I didn't need the door stop. I then put the door back on the bottom bearing hinge and returned the top hinge. After replacing the food, the job was done and the "catch" and noise were gone! Success!
Removed the door marking the top hinge placement prior to removal. Pulled the door the rest of the way off. There wasn't anything keeping it attached on the bottom right side. Turned the door upright dug out the old broken cam and replaced it with a new one. Thank you for your web-site. It saved us $$$ you have gained two new fans to your web-site. I have shared your link with many. To to anyone who is having a popping noise when you open your door. Do panic. Log on to Part Select .com. It is your only source of sanity.Thank youLiz
The door was removed, and the piece of the old bearing was pulled out. The new piece was inserted, and the door was, once again, attached to the refrigerator.
First I removed hinge cover on top of refrigerator door with philips head screwdriver, then removed (2) 5/16 bolts to remove hinge bracket remove refrigerator door, remove broken bearing hinge at bottom of refrigerator door, install new hinge, install refrigerator door good as new. Took less then 5 minutes.
watched the video, ordered the part and handed it to my husband. He quickly removed the hinge cover and took it apart--the lower door bearing was tightened with glue which made it difficult but once that was out of the way, it was remove, assemble and back in business. Thanks for making it "do-able". C and D in New Mexico.
After looking up the parts on the website (very easy to navigate). I speant 10 minutes changing the 2 parts.For $ 18.00 in parts (including shipping) I saved $ 150.00 on a service call.
I cleaned out the refrig door, unbolted it from the top and removed the door. Then I replaced the broken plastic parts, reinstalled the door and bolted it back up. Very simple, very easy!
Took door off and replaced part and door back on...... easy!!
Exposed and removed the screws at the top of the door. Removed and replaced the bearing and plate on the bottom of door and put it back together. Honestly, this is the easiest repair I ever made. The biggest chore was removing the contents of the door before taking the door off. Also was working alone, an extra pair of hands to hold the door would have been helpful but not necessary. Be prepared to never hear that horrible clunk again!
I watched the video on line after identifying the proper parts I needed. When the parts arrived I followed the easy instructions I had watched and proceeded to turn off the unit and remove the items and shelves from the door and then removed the cover plate and two screws from the bracket holding the door in position. Laying the door on a blanket I was able to quickly remove the broken part and insert the new plastic bearing in place. I then removed the plastic part on the lower bracket and installed the new piece. The door was easily put back on the refrigerator and was aligned perfectly. Putting shelves and items back in place was still less then the fifteen minutes time.
Emptied contents of door. Removed door by removing top hinge. Turned door upside down. Removed broken hinge bushing and installed new one. Reinstalled door and top hinge. Door works perfectly.
pulled door off and replaced with new henge part.went likeclock work.probably saved 150 cutting out repairman
My hubby and I simply lifted the door up and out of the hinges and while, balancing the door on a footstool, took off what was left of the old closure bearing, stuck the new one up inside the hole and placed the door back down on the fitting. VERY EASY!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.