Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS429803
Sold individually. Also known as a short door closing cam.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
Sold individually. This cam is located at the bottom of the fridge/freezer door.
Couldn't have been an easier. Removed the screw/nuts from the top of the fridge door that held the door in place and removed the door. Unscrewed the holder at the bottom, replaced both parts and put the door back together. It took me longer to get everything out of the fridge door than to replace the parts. EASY AS COULD BE!!!
Help other customers find the most helpful instructions.
Were these instructions helpful?
I removed the door and replaced the broken hinge bearing with the new part and the door works great!
Purchased 2 parts on line, easy replacement, one man job, 4 nuts to remove and replace. 20 minutes
I followed the website instructions, step by step. The web instructions were great. Easy to understand. Complete. Do yourself a favor.... just follow the instructions off the web! Great service! I am so happy to have found Part Select and will recommend to my friends.
Simply removed two screws from top hinge and lifted door off bottom hinge. Next leaned door over and removed broken portion of bearing. Finally reinstalled door and works like a charm. Thanks too this site painless repair. Oh ya part is a perfect fit. Thanks ClayP.S. Would recommend to a friend. Note shipping WOW. Please consider using US Mail. Shipping more than part. OUCH.
Removed the top hinge pin and lifted the door off the bottom pin. Removed and replaced the bottom defective parts and reinstalled the door. Reinstalled the top hinge pin which completed the project.
I removed the top door hinge, and then lifted the door off the bottom hinge. The bushing which helps close the door was completely worn away. I pulled out the left-over bushing parts, installed the new bushing I had ordered fro you, and reinstalled the door. It works perfectly now.
Unscrewed top part of door,put it down and replaced hinge bearing,apply some grease,put door back and done very easy do it yourself.
remove everything from door, remove plate and screws from top of refrigerator, disconnect water feed for ice maker underneath, remove door, be sure to remove any remnants of old parts, replace with new (i had to make a hole in the bearing for water feed, I may have ordered the wrong part, but it still worked, fridge side would not have water feed to worry about), put door back on, re-connect water, replace screws on top.........done.
Removed the door , removed to old bearing , inserted the new. Works like a charm Thanks Marvin
I first removed the hinge cover at the top of the door. This allows the door to be lifted off of the bottom hinge. After removing the remnants of the broken part, I slipped the new door closure bearing in place. I reinstalled the door by sliding the door over the lower and upper hinges. Be careful to note that an additional part "door closure" may be necessary as in my case this was all one unit in the broken one.
Removed screw from upper plastic bearing cover, removed cover by sliding forward. Removed two screws that retained the upper bearing plate, pushing refrigerator door against refrigerator so as not to fall, slid upper bearing plate up and off. Lifted refrigerator door upward and away from refrigerator. Removed screw retaining lower bearing plate and had to remove door closing bearing from door by breaking with screw driver as part of bearing was broken and remained in the door. Re-installed new parts and re-assembled. Door works great and all parts fit perfectly.
1) Empty the refrigerator door (Good time to clean it too!)2)Take the cover plate off the top hinge. 3)Remove the two screws on the top hinge (Keep the door closed) 4) Oppen the door and lift up. It will lift out of the lower hinge. 5) Remove the screw from the door close plate and replace. 6)The door closure bearing is in a hole on the lower part of the door and is likely cracked in two. Remove the upper part from the door. You may have to remove the plate. 7) Replace the plate if needed and insert the new door bearing in the hole. It only fits one way due to the shape. 8) Complete steps 6 through 1 in reverse order. The whole thing takes 15 minutes. One person can do it. The door is very light.
This repair was the easiest I have ever done. Took longer to clean the door before putting it all back that to replace parts.
with helper to remove door and lay flat to remove bearing with needle nose pliers. Popped out old and installed New one by pushing in. Reinstalled door and tightened small screws making sure door aligned properly. Replaced Door Bin.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.