Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS429725
This door bin holds items on the door of your refrigerator. They are sometimes called Cantilever Shelves as they are supported by the back of the shelf itself to the door of your refrigerator.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
Replaced bottom door bin being careful not to put stress on the tabs to fit into molded area in door.
Help other customers find the most helpful instructions.
Were these instructions helpful?
We live in rural SW Missouri, so I am very dependent on the internet. I found PartSelect on a Google search and simply inputted the modle number and serial number for the refrigerator and there it was. I was able to order the right part the first time and repair the refrigerator myself! No serviceman needed here!
Not much of a repair. Just swapped the old bin with the new one.
The website was easy to navigate. Loved the schematic drawings of the appliance, it made it easy to find the part you are looking for without the guesswork (part names are sometimes not intuitive). My parts arrived promptly, the price was competitive, everything fit beautifly as expected. Would recommend this merchant, will shop there again. THANKS !
No tools needed. Just had to slide the bin into place. HOWEVER, the bin has a jig-jagged style plastic groves on each side that need to be slide carefully into place. I couldn't get the orginal bin out in order to wash it. It looked easy - just slide it up and out of place, but when I did that the back, inter-locking pieces cracked off. I believe this is a terrible design and the bin should be replaced at the manufactures cost! The other bin slide in there with some elbow-grease. Good Luck!
I snapped off the old, broken parts of the shelves and in the side by side fridge, I just popped on the new shelf. In the White Westinghouse freezer on top fridge, I had to remove (it snapped right off) the broken side shelf retainer bar end cap from the fridge and remove the broken piece piece of plastic from existing shelf retainer bar end cap that was stuck in the retainer bar. I used a letter opener to help get it out. Then I snapped the new door shelf retainer bar end cap into the bar, and snapped the bar end cap back to the door. Both repairs took less than 5 minutes..........and I am a female who isn't very handy!!
The repair was not my worry, but ordering the correct part. I was so pleased with this web site and the quick delivery of the part that I ordered. I easily found the bin I needed for my refrigerator and had the part at my doorstep with two days. I am extremely happy with this site.
I removed the screw in the plastic cover on the top of the fridge that covered the fridge side hinge first. Then, I removed the two nuts with a nut driver that hold the hinge in place. After removing the two nuts and the hinge, I lifted the door up and out of the bottom hinge and placed it on a flat surface. I used a pair of pliers next to pull out the broken hinge bearing from the bottom of the door itself. After removing the old bearing I inserted the new bearing in the door. Next, I put the door back on making sure the hinge went into the hinge bearing and put the door in the closed position. After that was all done and the door was set properly, I put the top hinge back on with the two screws and put the plastic cover back in place. Took 20min to complete. A second set of hands would have been helpful with putting the door back on, but it can be done by yourself.
I pulled out the old support stud with a pair of pliers, pushed the new stud in, and gave it a few taps with the hammer to secure it in the fridge wall. For the door bin I just slid the new bin in place.
Simply put the items in place...was very please with the parts. They were excactly as advertised and fit perfectly. The delivery was also very timely...thank you very much.
We considered tape and glue, but we knew that it would look like crap and wouldn't last. Fortunately the bin had a part number on it, so it was easy to order the correct part and it fit perfectly.
I ordered the parts by studying the diagram and they were perfect. Thanks for making it so easy.
Replaced the bin took less than 5 minutes. Very impressed with the service we got. The part came in 1 day!!
Easy. Just placed the bin in position.
I replaced the items myself, there was not much to it. I must comment on the sight. It was very interactive and easy to use!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.