Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS422630
This is a white cut-to-fit door shelf retainer bar.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
I checked the defrost timer (bottom front of the freezer / outside). I advanced it to send it into the defrost cycle. The heating elements in the freezer (behind the panel) did not heat up. I cut the wires going to the defrost thermostat. Turned the power back on, made sure the defrost timer was still in the defrost cycle and checked the voltage at the wires to the defrost thermostat (before the heating elements). There was power / voltage there. I jumped out / bypassed the defrost thermostat turned the power back on and the heating elements came on. The problem was the defrost thermostat. So I replaced it with a new one from PartSelect.com. How it works...When the defrost timer is advanced to the defrost cycle the switch closes sending power to the defrost thermostat. If the temperature is low enough, the defrost thermostat switch will close and sends power to the heating elements. When the temperature rises high enough about 55 degrees the switch at the thermostat will open and the heating elements will turn off (not allowing the freezer temperature to get too high, just enough to defrost the coil). The refrigerator will turn back on when the timer advances. The defrost timer will defrost every 8-12 hours.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I took a look at the web site where I purchased the parts, then I took a look at the paper enclosed with the order. Thankfully, I have a battery operated screw driver since there are so many screws. There are plenty of screws in my refrigerator and freezer doors. I thought that since my old door gaskets were all chewed up looking, if I changed them, the 10 year old air conditioners and the old fashioned light bulbs to instant on energy saver light bulbs, the electric bill would become more manageable. The refrigerator and freezer door gaskets were the first step. They were easy to swap out. You just need to empty the door of all food items, then pull back the old gasket to see the screws. There are alot of them. You should leave 2 loosened screws on each side of the refrigerator door to hold the panel in place while you work and remove the rest. Then you can remove the old gasket and slide the new one into place. Make sure as you tighten the screws and replace the ones you removed, the new gasket fits into the door panel groove securely and is in place as you tighen the screws. Make sure it is in place all the way around the door as you work. You repeat the procedure for the freezer using only one loosened screw on each side to keep the interior panel in place while you work. It takes some time due to the number of screws, but the work is pretty easy. I never even broke a nail. The end caps for the shelf bars just snap into place just as the old ones can be snapped out with a bit of pressure. They do not have to be wrestled and you need to work carefully so that you do not break them. (I ordered an extra just in case, but I didn't need it. I will have it in case I need it in the future)My electric bill dropped from $450 to $110 a month with all the improvements I made. Thank you Part Select for taking the fear of screwing it up, out of the repair process and making it manageable. I can afford my electric bill now. Thanks for your help.
I was missing a door shelf, and until I saw your diagram, I didn't know I was missing egg tray. .
Placed door rack in end caps and snapped on to door
The replacement part was a bit too long (about 6"). Measured length of the existing bar that was on lower shelf and used a rotary tool with a metal cutting disc to make the same length. Everything snapped into place easily.
I want to start by saying that I am female and want to let all females know that we can do home repairs! My story is not just about the repair but the wonderful customer service at PartsSelect.com. I have used them MANY times to order missing parts for appliances (I own rental property and tenants are always "losing" or breaking appliance parts). This particular time was the first time I received an incorrect part...not sure if it was my ordering or the wrong part was shipped. I contacted PartsSelect.com by email and got a REAL response within 24 hours. The customer service person who responded, immediately credited my account and "found" the correct part to order and less than 48 hours after my first email to them, my new part is already on it's way! I know it will only take minutes to finish my repair and am really impressed with their response time and professionalism when there is a problem. As a rental property owner, I will continue to use and recommend PartSelect.com.
The parts were sent out fast, but the wrong retainer bar. My apartment bldg is in another state, by the time I got up to my apartment bldg to do the repair several weeks had passed and i lost the bill to get a refund and now I have a $40.00 strip of metal sitting in my garageSo the fix time would have been 15 minutes had I received the correct part.
Placed end cap on one end of rack and attached to one side of the door by applying hand pressure.Inserted the other end of the rack into the end cap'and again applied hand pressure to insert into slot, Repairs completed.
the repair went fast and easy. my boyfried measured the retainer bar, cut it with the hack saw installed the right and left side door shelf end cap and inserted the door shelf retain bar. the door looks great. would highly recommend your website and customer service. thanks again.
I snapped one of the end caps in, put the rack rail into the cap, placed the other cap on the other end, and snapped that end in. Because I received the exact parts needed, the entire repair took about one minute.
I had to cut the rack itself. It was too long. So make sure you have a hacksaw ready. But first look in a junk yard the rack piece is too expensive for a piece of metal
I measured the width I needed and used a handsaw to cut it the proper length. Then I snaped the pieces in and it was a perfect fit.
Ordered the parts from the product discription (photo) as well as chart showing actual size. Got the parts( in two separate shipments) cut the bar to length and snapped them inot place. Bingo!
The only problem I had was that the end cap was sent before the rack. This refrigerator is in our cottage and I brought up the end cap while waiting to receive the rack. I couldn't remember where I put the end cap, so when the rack came it took me a few weekends to find the end cap. Once I did, it took me less than 1 minute to repair. I put the rack on the end caps & pushed the end cap in place. DONE!
We just put the new end parts into the door and then placed the bar inside the caps. We had contacted our appliance dealer at least three times to get parts for us but to no avail. A friend told me about your website and the rest was history ----- and easy. Thank you.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.