Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS420766
This linkage attaches to the door spring.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
Per the recommendation from PartSelect.com, I purchased 2 new springs and 2 new clips - one set for each side. With the bottom cover plate removed below the door, I removed the remaining spring and clip and installed the 2 new springs and clips by hand. The door now opens with resistance and won't even stay completely opened unless the lower dishwasher tray is rolled out on it. it's like new.This is the second repair to this dishwasher. Last year I replaced the door latch that had broken with a replacement purchased from partselect.com. That repair was also quite easy.PartSelect's full part brochures by model made identifying the needed parts simple, and the replacement a breeze.I even repaired my refrigerator ice maker a couple months ago after purchasing a new control module, and saving both a service fee and the probable full price for a new ice maker.I've repaired my electric clothes dryer too, and hadn't even thought about all the repairs I'd done thanks to this website, until I told the story of my dishwasher.I've probably saved $1000 already. Wow!I love this site.
Help other customers find the most helpful instructions.
Were these instructions helpful?
One Roller detatched and hit the heat coil and melted. Both of the Spring Linkages borke. It's was quite obvious they were made not to last long. My Husband did the repairs. Thank you for asking.
All I had to do was replace the spring and retainer on the side of the dishwasher which amounted to pulling it out far enough to reach the eyelet that the hook went into and then stretching it to the retainer attached on the other end. I really like partselect, I have done some things in the past and they are very helpful on the site and on the phone and I would recommend them to anyone and I would not normally do that unless it has been an excellent experience.
First unplug the unit.Second remove the kickplate. When you do this pay attention to the position of the insulation panel. It is confusing as to how it is put back together. Simple if you see how it comes apart.Third unsrew the screws that hold dishwasher in palce under the counter top.Genly pull the appliance from under the counter top. Understand the copper piping connected to the unit for water will only allow you to pull it out a few inches. Otherwise you would have to turn off and disconnect the water supply.Reinstall the plastic clipsand springs. There are several holes in the frame of the dishwasher where the springs will attach. The further back you attach them, the more tension will be applied to the springs. This part of the operation is somewhat trying as you have limited visibility and access.When springs and clips are installed, test door, slide unit back in place, reattach kickplate and insulation panel and then reattach to countertop.All in all relatively simple and doable. If I had any problem it wasnot paying attention to how the insulation panel and kickplate came apart. No big deal.
I found the parts needed on Part Select and read comments by users. I took the suggestion to buy both springs at the same time and the door linkages too. Although they were pricey, the parts arrived in a few days and were absolutely perfect. To my suprise and delight, the entire fix for the broken spring and link and the opposite spring and link were easily accomplished in less than 10 minutes. The links just hook directly onto a small hook on the door and the springs have specially bent ends that fid the linkage and then the adjustable length holes on the door. It made me feel quite manly for about fifteen minutes as I made everyone in the house open and close the dishwasher door several times.
After having a repairman out to changing the door handle and seeing how easy it was...I decided to try to fix the spring issue myself. I am fairly confident with most small fix it items in our house, so decided to order the original spring & linkage. The website was pretty self-explanatory, but wished someone hinted that when you have one broken spring, the other usually goes out within a short period of time. Note to others, ordered 2 springs & linkage and avoided another shipping charge. Do both springs at the same time, and will save you time in the long run. Otherwise, super easy to change out...wish all appliance issues were this easy to fix. I did not need to take of door off....I just needed to lay on floor & become a little limber. Other than that...super easy.
Removed the bottom panel on the unit (2 screws hold it on) and pulled the dishwasher out about 4"--after turning off electricity to the unit. Removed the broken spring and the old linkage and replaced them with the new parts. Pushed the diswasher back into place, and replaced the bottom panel. Turned on the electricity and the diswasher door is "good as new." This is quite simple to do; just takes patience.
Previous self-repair instructions provided on this site were very helpful. I started by removing items from under the sink and inspecting drainage and water hoses of the dishwasher to determine amount of "play" for sliding the washer out. Next, remove the two screws that secure the washer under the top of the counter. Then, remove the kickplate and barrier at the bottom. The washer then slid easily out far enough to explose the spring connector arms. I removed the old springs from the floor and the pieces of the old links (one link was ok, but I saved it for a spare). I installed the links and springs on both sides and connected to the first hole. By the way, the hole in the lower frame relatively close behind link is NOT the spring connection hole. There are a series of holes farther back. After testing the door and re-hooking the springs twice,I decided that the fourth hole gave the tension that I wanted. Now the door will come up about half way on its own, but will stay fully open when pulling out the empty bottom basket. Slide the washer back under the counter, being careful not to catch the insulation at the top and sides of the washer. Line up the top screw holes and install the screws. Install the barrier panel and kickplate at the bottom. I had to "fiddle" with the kick plate and barrier panel a little to get it right because I did not play close attention when removing them. I probably saved $100 by doing it myself. My wife said "It's just like new!"
Repair was easy. Unfortunately I really didn't need the springs or linkage, but I couldn't see that until I took the dishwasher out from the counter. The springs were not stiff enough to keep the door from just falling open. So I cut about an inch off the long end and bent it into a hook. I didn't need new linkages the old ones were fine. The gasket made the biggest difference and went in very easy. The door will be difficult to close for a few times then everything works great.
Removed the two bracket screws attaching the washer to the countertop, and removed the kick panel beneath the door. Pulled the washer out enough to access the spring arms. Replaced the broken spring arms, and pushed the washer back into it's space, re-attaching the kick plate, and securing the lock tabs on top of the washer. Used one phillips screwdriver, a #2 tip. That simple.
I received the parts 3 working days from order. They were in perfect condition and exactly like the originals.Pulled dishwasher out from under counter. Removed door. Replaced drain hose. Replaced gasket. Replaced springs. Put door back on. Tried rinse cycle. Placed dishwasher back under counter. Works like new.
there were two screws securing the dishwasher to the counter top, I took those out and pulled the dishwasher out about 12 inches the spring and plastic linkage was visible, I just unhooked the one that wasn't broke and installed the new linkage and spring the same way it came off the one that was broke was even easier i just looked at the one that wasn't broke and put the linkage and spring on the same way, I pushed the dishwasher back under the counter top and put the screws back in took about 10 to 15 mins I am an ex-mechanic so I am pretty fast anyway.
pulled of dishwasher a couple of inches,installed springspushed dishwasher backdone!
I took the door off by removing the two screws that hold the it in place. I removed the two screws that secures the diswasher to the cabinets. I slide out the unit approx 3 inches. I attached the new spring and linkage (very simple to see how it connects).I pushed the unit back in, secured it to the cabinet and put the door back on.That's it! Easy. I saved at least $150 service call with Sears.
Slid dishwasher out from under counter about six or eight inches. I was able to see where to attach the new spring and linkage. There are many holes in the base of dishwasher so that you may adjust the door balance by choosing a different hole. I used the same one on the right side that was used on the left side and it just balances perfectly. Slid it back in and attached the screws at the top and adjusted the feet with a 3/16 socket and small rachet;took about 30 minutes.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.