Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS418632
This part mounts on the inside of the rear cabinet.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
well, i started at the top and worked my way down. by taking the top off, it gave me more room to get the dryer tub out. took the two screw`s out of the vented plate on the back of the machine to undo the belt. this is a stackable washer-dryer combo, so next i took off the white plate on front between washer & dryer. took off the control panel, unpluged it, then took dryer door front off. then removed the two screw`s that hold that bracket on ,in the back of dryer, pulled the drum out & replaced the belt, but before replacing anything i took the shopvac to it , there was alot of lint in there.when replacing the Grounding Ball Clip & Grounding Ball, i took a one inch by two inch magnet and used it to hold the Grounding Ball & Clip in place so i could get the two screws started in the Drum Support Bearing & Bearing Bracket. after installing that i put the shaft in place & lined the dryer tub up with the 3 screw hole`s ,and boom, bang, pow...nothing to it. it`s easy...parts came very fast....Thx PartsSelect.com...i`ve told all my friend`s about PartsSelect
Help other customers find the most helpful instructions.
Were these instructions helpful?
First, I removed the top panel which is held on at the front by pressure clips. Second, I removed the entire front panel which entailed removing 2 screws and 2 wire couplings. Third, I removed the 3 screws on the inside center of the drum which turned out to be unnecessary. Fourth, I slid the drum forward in order to access the rear bearing. Lastly, I replaced the entire bearing assembly including the shaft, bracket, bearing, grounding ball and clip. Again, probably not needed but I had ordered the parts in advance in preparation for the worst.
First: Remove front and top coverSecond: remove electrical cover assblyThird: motor belt removedFourth: drum assbly and bearing shaft and bracket bearing replacedNow I need urgently (already ordered) the thermostat and glide drum
Took off front panel, removed drum and replaced parts listed. A bit tricky to keep small parts in place. However, masking tape helped. Best of all was the online diagram of how the parts were assembled. In addition, taking step by step phone pixs aided in replacing parts since there was some down time between diagnosis and installation.
Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum. Remove the drive beltRemove the drum.You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.Re-install the parts. I used bearing grease to make it run smootherAttach the new shaft to the drum and reinstall the drum (its best done with help)Re install everything back again. And you are done
From previous responses on this site. I just followed their lead. If I had not found these folks, and the responses, it would have been a nightmare. It looked like and I thought the dryer came apart from the back! But in reality it comes apart from the front!! Absolutely fantastic site and help. Fast shipping, I ordered on Wednesday before Labor Day, didn't expect the parts until the following Wednesday, but received the parts on Saturday morning, and had the dryer back running by Sunday AM. Never even ran out of clean clothes!!!!!
Took off all controls and panel. Removed the top. Pulled out the drum. Unscrewed shaft and bearing holder. Replaced all parts and started it back up. --The parts were shipped timely,
took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new dryer
replaced bearing and shaft new belt and everything works just fine
removed top and front panel on stackable dyer unit. 3 screws at back of the inside of the drum, and the drum was out. installed new bearing and belt and all was good.
I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.
we removed the top of the dryer which was clipped on. then removed the front, including the door, being careful to unhook the electrical elements. then we removed the screws that attached the dryer drum to the back of the shaft. then we took the shaft out of the bracket. then we removed the plate from the back of the dryer that held the ball, the bearing and the bracket together. then we waited for parts and thanked God that the weather was fair so we could hang our clean clothes out!!! the parts came ahead of the rain so it was reverse order. then try the dryer!!!fantastic!! to qoute my kids "you rock"
Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.
removed top and front of machine. removed drum. replaced shaft, bearing bracket, and support bearing from inside. replaced grrounding ball and clip from outside. reassemble.this should be available as a kit, and should include high temp grease to put in bearing bracket
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.