Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Katie W - June 28, 2020
Verified Purchase
Simple repair/Item exactly as described
Super easy repair..only 1 bolt and a water tight cover. I did have to use a pair of channel locks to get the water tight cover out (my washer is probably about 20ish years old) and a rubber mallet to get the new agitator all the way down on the post so I could get the bolt in. But the entire fix only took like 10 minutes.
★★★★★
★★★★★
Linda R - May 21, 2020
Verified Purchase
Make sure you have the washer underneath this agitator when you screw it down. IMPORTANT.
Part arrived in good condition and on time. Remember the washer between this part and where you screw it down or it will not be tight enough.
★★★★★
★★★★★
Dominick C C - February 3, 2018
Verified Purchase
The right part
The part was right and packed well. Arrived in a timely manner.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 8 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Agitation weak
Got the washer used. Agitation was okay, but the screw part of the agitator was very weak and kept slipping, so bought a replacement agitator. This DID NOT fix the problem, it remained the same. Watched a video on this site about the part under the agitator, whereupon we saw there was supposed to be a washer on top of the spike-thing
... Read morewhere you screw the agitator down. THAT was the problem. That washer was missing, and when we replaced it, the agitation was fixed! Very much appreciate this site.
Read less
Linda from WEST POINT, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken agitator in washer
5 mins. Take off fabric dispenser. Pop off cover underneath. Unscrew bolt. Pop off agitator. Put on new one. Screw back down. DONE :0)
Elliott from Orinda, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
25 of 33 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator making clunking niose
Removed the top of agitato removed bolt, R&R part ,put bolt an top back 3min. Top
Lee from Willcox, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
11 of 19 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
CLothes weren't getting dry enough for the dryer.. also made a squeling, rubbing noise while aggitating. Had a repair man for my dishwasher..told him I thought it was the transmission.. he hand turned the aggitator and said that was the problem.. Just needed a new aggitator....whew what a relief!
I'm a 70 year old widow.. ordered the part which came in 2 days..(.very reasonably priced) My son came over and in no time had the old out and new in...works like a new machine... Thank you Part Select. A few months ago ordered a stove ignitor..it too came really fast... stove is good for another 15 years..LOL
Bonnie from Trevor, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
11 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
agitator not turning on top, clothes not clean
ordered part from parts select, it was the wrong part,( all my fault) they refunded part upon return and sent the new part, the return was easy and prompt, new part arrived, 15 minutes wife was washing and happy again, and we all know, happy wife happy life, thanks part select!!!
Scott from Palmyra, TN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
18 of 29 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
agitator was stripped, so it kept slipping.
removed old agitator by loosing a bolt at top, after removing the detergent dispenser. agitator came off easily, new one on, bolt on with rachet wrench, dispencer on. works like new. thanks for the great service. the part came in faster than i thought it would, and i would have had to travel for miles to get a part around here. VAL
VALERIE from TUPPER LAKE, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set
12 of 20 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The upper part of the agitator wasn't working.
I removed the bolt holding the agitator in the tub and lifted the agitator out. There seemed to be a part near the top that was not engaging. I decided to order a replacement to see if that was the problem (my local repairman had guessed the problem was in the transmission and said I should just replace the machine.) I ordered the part on
... Read moreline and it arrived in only two days. I was very happily surprised by the speed with which I received the part. I put the new agitator in, tightened the bolt and ran a load of clothes. All worked perfectly
Read less
Bob from Estes Park, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
21 of 27 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clicking due to agitator dogs slipping
One bolt (after removing the fabric softener dispenser and a water tight cover you will see it). Remove the bolt and slide it straight up and then it's the reverse to put in the new one. Very simple repair and very inexpensive if you willing to do it yourself.
BRIAN from UPLAND, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
81 of 102 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joe
December 2, 2017
The fabric softener bowl looked dirty so I removed it to clean, the area under the bowl was dirty so I removed it, the area around the bolt was dirty so I removed it and pulled off the agitator and it along with the bottom surface under the agitator was black. I cleaned what I could but the inside of the agitator is dirty. Any way to take agitator apart to clean it. Also, any suggestions on how to prevent further dirt build ups?
For model number GLWS1349AS1
Hi Joe, Thank you for the question. Unfortunately the agitator does not come apart. You can try to run a load with no clothes and add vinegar to the water. Doing this once a month should help with build up. Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Cheryl
October 10, 2017
I am trying to remove the agitator, I removed the softener cup but I am not able to get the waterproof cap off to get to the bolt any suggestions?
For model number FWS845GFS1
Hi Cheryl,
Thank you for your question. It is difficult after years of use. You may need a strong set of pliers to be able to twist that cap off. Unfortunately that is the only way to remove that seal. Good luck with your repair.
4 people found this helpful.
Was this helpful?
Thank you for voting!
ERICA
August 6, 2018
Did as instructions say, agitator will not lift off. It is a dual agitator. Machine spins and drains but agitator won't agitate.
For model number crws57c0as0
Hello Erica, thank you for your question. The agitator is held into place by a bolt that is under the cap and seal inside the agitator. If you remove the fabric softener cup and look down inside you'll see a cap with a black seal around it. The cap twists off, then the bolt can be removed and the agitator lifted off and out of the tub. If the unit is spins and drains, but isn't agitating, check the belt, pulley, and tensioner under the tub by the motor as well. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Joe
June 26, 2021
Banging noise when agitating
For model number FWS6976FS1
Hello Joe, Thank you for the question. We suggest checking for wear or damage to the Spin Bearing, Upper Spin Bearing Washer and the Tub Seal Assembly. We hope this helps!
Washer is about 20 years old. Agitator seems loose and noisy. Any suggestions?
For model number Gibson Washer GWS645RHS0
Hello Suzanne, thank you for contacting us. The most probable cause of the issue is a damaged agitator drive block, part number PS1152574. Also, please check the agitator screw and make sure it is properly secured. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
