Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS418120
This dryer heating and housing assembly has terminals at four o'clock. This E-line assembly comes with a felt strip and insulators already attached.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
Disconect the dryer from the main power source.1) Remove the two screws from the rear / upper panel (below the control panel).2) Snap the front side using a flat head screw driver.3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.4) Remove the rear motor access panel (two screws) and appying tension to the spring remove the belt.5) Pull the drum upwards (verticaly) unnapping it from the rear wall and remove it horizontally through the front panel.6) Disconect the four leads to the heating element and remove the four screws from the rear of the dryer and replace the heating element. Follow the same steps backwards to put the dryer together again.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I unlatched top panel then removed two screws holding front panel on. I then lifted drum out of hanger to make room to remove element. Disconnect wires to limit switch and element. I then removed four screws on back of dryer that hold the pan. I removed old assembly and replaced with new one. Assemble in reverse.
I followed others suggestions with numbered steps and listened to others suggestions about replacing other parts while in the dryer. I took the dryer apart and cleaned it out well. I used acetone to remove the glue from the felt and Drum Glide at the top of the Drum. It worked much better than Goo Gone. By doing the clean up and evaluation one day, I ordered all the parts that I saw were worn or difficult to get to. I replaced the Heating Element only because the old one was very brittle and to get to it again would be difficult. Also, I followed other's advice to photograph the parts before removing. It was easy to remember how things went if I had a photo to refer to. When the parts arrived it only took about 30 minutes to install them all because the glue removal, lint removal, and parts removal had been done another day. I should add that I am a 66 year old woman and found the job quite simple. Excellent web site. Thanks to others for the step-by-step instructions. Oh, to hold the Drum Glide and felt in place while the glue cured, clothes pins work great. I let the glue cure overnight to make sure that it was really secure.
It was too easy: 1) remove the back of the control panel 2) disconnect wires to the switches and mark them for reassembly- I used masking tape and gave each wire and connector a letter- "a" "b" "c" etc; 3) remove the top of dryer by using a flat head screwdriver to pop the 2 pressure fasteners on the front; 4) remove the front of the dryer- remove the 2 screws fastening the front panel to the sides and lift up until the bottom pressure fasteners pop; 5) remove the belt from the pulley and tensioner- I used a digital camera to take pictures so I knew how to re-thread the belt; 6) remove the drum- pull up on the back of the drum with the belt and then pull the drum through the front of the dryer-it's a little smaller than the front opening so you need to pull on the sides of the dryer; 7) replace the heating element by (a) removing the overheat sensor and (b) removing three screws to remove the heating element from the back of the dryer; 8) replacing the rear drum bearing by (a) removing the bearing asssembly from the back of the dryer-2 screws, and (b) removing the bearing roller from the back of the drum- 3 screws; 9) assembly is the reverse of disassembly. Again it's too easy. I'm a lawyer with no mechanical training. Thanks to Parts Select for making finding the parts easy and saving me a lot of money.
Removed top using a butter knife to release the two tabs in the front(between the top and the front). Removed the front(two screws from the inside. removed rear louver panel(four screws). reached in through rear panel and released belt. removed drum assembly and change out, bearing assembly drum and bushing assembly in the back panel, being sure not to forget the grounding bearing(had my 9 year old give me an extra hand to hold the ball bearing on the back..Replaced the slider felt on the drum and the belt since i had it apart. Also replaced the seal from the front panel to the blower motor.. while it was apart i cleaned the inside with bleach and a rag. reasembled a tryed it out. Run like a new dryer- Nice and quiet.- It had been sqeeking for months before the it stopped working. the time it took to fix it was a lot less hassle than it would have been to buy a new and get rid of the old one. And it saved me money. I love saving money!! I would recomend partsselec.com t.good prices,fast shipping, got what i needed. What more can you ask for..
I waded into this project without knowing what I was doing and as a result did much more work than was needed. What I should have done was 1) open access panel at lower left of back of dryer and rmove belt from pully 2) push screwdriver in against clips in seem at top front of dryer (where top meets face) and lift top up and off hinges at back 3) remove screws holding front of dryer to the sides of the dryer cabinet (about 1 foot down) and swing front down on hinges at bottom 4) lift dryer drum straight up out of the bracket at the back of the dryer 5) remove wires from the dryer element and heat sensor on the heater pan (about 4 and 1 o'clock respectively wires are on tight, may need plieres) 6) unscrew heater pan from back of dryer 7) remove heat sensor from old heater pan and put on new heater pan 8) screw new heater pan to back of dryer 9) replace wires to elements and sensor, you may want to "crimp" the connectors onto the tabs 10) replace dryer drum slipping back into back bracket, be sure that dryer belt is around drum as when you openned the dryer 11) lift up front so that drum fits around and is supported by flange molded into front 12) replace screws that attach front to dryer cabinet 13) replace top of dryer (put back on hinges at back and lower onto clips in front 14) put dryer belt back on pully and replace access plate.
1.Remove 2 screws and the air intake grill on the back of the unit. remove the drive belt. 2. Remove 2 screws on rear of top, slide top back and remove. 3. Remove 2 screws about a foot down on the inside on each side of the front cover. Remove four screws that secure the plastic control panel and the front panel that are right behind the control panel on the top. Disconnect the wiring harnesses, cut the nylon wire tie that is closest to the front cover. 3. lay unit on its back and and remove the two screws on the lower edge of the front panel, take your putty knife and slide it in the gap between the front panel and the dryer cabinet and release the two spring clips on both sides. Then you can lift off the front panel and control panel, set it to the side. 4. Remove the screw and the nylon guide from the center of the top front case crossmember. Remove the three screws on the inside rear of the drum, lift out the drum and set aside. 5. The drum pivot just sits in a nylon socket, pop it toward the top of the machine and lift it out, you may want to clean it good and re-lubricate it on reassembly. Disconnect the wires from the heating element and the heat sensor. 6. Set the cabinet upright and remove the four screws on the back side of the rear of the cabinet but not the two that are right in the center, they hold the pivot fixture and don't need to come out. The heater coil pan is now loose and ready for removal. 7. The seal between the filter housing and the blower housing was torn and this is an important part to have right, any air leak here will do the same thing as a dirty lint filter or plugged dryer exhaust and your new heating element will have a short, hot life. I pulled the old one off, scrapped the old glue off, applied the adhesive like the instructions on the tube say and after a few minutes installed the new seal then set the front panel to the side to let the adhesive dry. 8. The reassembly is just the reverse of the disassembly , use a couple nails or awls to help hold the dryer heater pan in place for screw installation and you might want to gentle squeeze the wire connecters if they feel loose, also check for clogged or kinked exhaust and stress the importance of cleaning the lint filter after EVERY load, it is small and all the air that cools the heating element must go through it, if is isn't maintained your new element won't last long. Have fun!
Other repair stories about this product are very accurate and I used them to do the repair, so I see no need to be redundant.I'd just like to draw attention to the following:Disassembling the dryer is somewhat easy. Replacing the heating element is very easy. Replacing the belt is very easy. Replacing the drum bearing is somewhat difficult. I purchased a "T" screwdriver in order to get more torque on the screws. When I had the drum bearing in place and the screws partially inserted, I laid a piece of thick foam on the floor and set the drum, bearing side down, on the foam. It is very difficult to get enough tension on the screws to get them through the bearing plate, but setting the drum up this way at least allows you to use gravity to your advantage.Thanks again to Part Select for making the part purchasing experience so effortless.Thanks to other writers of "Repair Stories" for making my repair so easy.
Tried to follow the directions of others but ran into a problem with getting the top panel off. This is how I did it.1 Disconnect power and dryer vent tube. Move away from wall.2 Remove slotted access panel in back of dryer and take belt off motor and idler pulley. Leave on drum.3 Unscrew the screws on the back of the top panel brackets( mine are silver) where they screw into the back panel and pull up and to the back to get the top panel off. Someone else said to slide a putty knife in the front to release the top but my machine has no spring clips.4 With the cover off you can see the two heat sensors and I tested them with a multi meter they registered 0 which meant they were OK.5 Remove the screws that hold the control board on and the plugs that are wired into it making sure that you draw a diagram to remember the wiring. There was a zip tie that I cut to be able to feed the plugs through the hole in the front panel that the wiring must go when the front panel drops down.6 Remove the screws on the top of the front panel and the screws on the inside of the side panel that hold the front panel secure.7 A lot goes on on step 7 because the front panel which is hinged drops from the top down to the floor. Diagram and remove all wires there are two green ground wires on the side, Three wires on the door lock, two wires for the light and wires for a moisture sensor. When disconnected feed the control panel plugs and other wires through the hole in the front panel and lift up and out on the front panel it will pop out. Lower it to the floor and let it rest there.8 Now you can get the drum out of the way by pulling up then out the front where the front panel is now on the floor. Leave the belt on it.9 Diagram the wiring on the heating element there are connections for the element and the sensor. They gave me a new sensor screwed onto the new heating element. Then unscrew it from the back panel the screws are on the back of the machine.10 Install is the reverse of the rip downIn hindsight I would have liked to have had the new part before I started the project because the wiring wasn't so fresh in my head a week later when it arrived even with diagrams. Over all it was very simple and took under two hours to complete. I did clean everything I could inside the machine and reglued a couple of the seals that had fallen loose. Works like new and probably went because of overheating with a clogged vent. Lesson... clean your dryer vent every year or sooner.
I removed dryer exhaust hose.unsnapped top cover the clips are in front and exposed inside of dryer,remove 2 screws on inside of front cover and set aside. remove lower cover in back and push belt extender until belt is loose remove 3 screws on inside of tumbler. remove tumbler out the front of dryer be careful not to damage belt set aside remove ball plate by pulling up and out it will unsnap. Now remove 2 sets of wires that are connected to heater element plate remove 4 screws holding element plate in place. Since dryer was all exposed I cleaned everything out with a wet vac put back together following instructions in reverse. Good luck
Girls you can do it on your own!The easiest way is taking the back off the dryer but if you can't do that just pop the top up and unscrew the front. Just make sure you remember how you take everything out and put it back in the same.The most difficult part is trying to line up the holes for the heating element, and holding it there while screwing the element in place. It's a breeze!
i first looked up the diagram for this model and checked for the best way to take the front cover off the dryer. after removing the front cover i start looking for the wires that connect the door switch and remove the wires. the front cover also supports the weight of the drum, so carefully pull the cover until the drum comes loose. at this point you can visually see the parts of the parts that make up the workings of the dryer. i first noticed the drum was coming out with the front cover at this time i knew the rear drum assembly was broke. i then took the belt loose from tension pulley and slid it off the drum and removed both from the cabinet. after the drum was removed i also noticed the heating was broken in several places. i removed four screws from the heating element assembly and also removed two wire that were connected to the element. with all pieces removed i checked the thermal switches, there are three switches, one on the heating element, one on the vent side and one on the back panel of the cabinet. i then installed the rear drum assembly and the heating element assembly and connected the wires. i then slid the drum almost all the in place and put the new belt around the drum and dropped the rear drum into the bracket that supports the rear drum then run the belt around the tension pulley and around the motor pulley. i then placed the front panel back in place and connected the wires for the door switch and lifted the drum assembly up just enough to insert the front panel door support into the drum and placed the clips in place, checked all connections twice and connected power back to the unit and turned on and run it through all its settings.
The repair was a bit more simple that what I had read here earlier, to see if I could handle it or I would have to call someone. The biggest relief was that I didn't have to remove any of the connectors from the control panel. Only 4 total connectors were removed at the Heating Element itself. Here's the steps I performed: 1) Pop the top off by prying the lid to release the 2 front clips and lift the top all the way up (like the hood of a car). Rest this against a door or wall. 2) Remove the rear access panel (2 phillips screws) on the bottom left of the unit. Remove the tension from the dryer belt and take it off the pully. 3) Go back to the front and remove (4 allen heads) from the back of the dryer drum. The drum should now have some play. 4) remove a plastic retainer that stops the drum from being lifted out. Now you should be able to lift out the drum. There is a ball & socket fitting that needs to come apart. This can be done by sharply lifting straight up. This gives you access to the heating element and you should be able to see where the coil has burned, thus opening the circuit. 5) remove (4 phillips screws) from the back panel of the dryer. Remove two pairs of connectors that attach to the heating element. Now it's out and you can begin the swap of the new element and reverse this process to put it back together. If I had to do this again, it would take less approx 30 minutes.
I took the repair video in with me and set my lap-top on top of the washer.My dryer did not match the type on the video exactly (mine has the controls in the front instead of on top and in the back) - however - the parts replacement for the rear drum bearing itself was the same.After getting the front apart and releasing the drum the rest was pretty easy. Didn't really need instructions for the heating element - that was an obvious change out.The tips on the video changing the rear drum assembly were very helpful.Just watch the vid and do it! It took me exactly two hours since I was also changing out the heating element and I did it on a Friday night while having a couple tasty beers.One tip I would give is the old grease in the bearing is very messy and I got it all over my shirt and pants - and when changing that stuff out don't lean on the front of the frame - I did and bent it out of whack a bit.The dryer runs like new now that it's done!
repair wasfairly easy,part select custemer stories and advice really helped.parts were shipped sooner then exepected,i will recomend part select to everyone i know.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.