Quick Question!

Have you ever purchased from PartSelect.com before?

418105-1-S-Frigidaire-131545101         -TRUNNION
418105-1-S-Frigidaire-131545101         -TRUNNION 418105-2-S-Frigidaire-131545101         -TRUNNION 418105-3-S-Frigidaire-131545101         -TRUNNION http://www.partselect.com/Schematics/Frigidaire/WKYR5BMR.gif


PartSelect Number PS418105

This part helps with the spinning and agitating cycles.

This part works with the following brands: Frigidaire, Kenmore, Gibson, Westinghouse, Kelvinator, Tappan, Crosley, Uni, Electrolux.

This part works with the following products: Washer, Washer Dryer Combo.

This part fixes the following symptoms:

  • Leaking.

Compare At


You Save


Your Price

Order within the next 9 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 1 reviews What's this?
1-1 of 1

229 of 286 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Socket set
Customer: Rick from Walkerton, IN

The primary problem was that the tub seal assembly was leaking.

1. I began by removing the two screws that hold the front panel in place. I then lifted the top free of the front panel and tilted it back to get it out of the way.

2. Using my fingers, I released the tabs that connect the tub cover to the tub. It took some effort to remove the cap("Mechanism") over the bolt connecting the agitator to the agitator drive block because I didn't want to break the tab. Once removed, I removed the bolt and the agitator. I then removed the two bolts that clamp the Trunnion to the agitator shaft.

3. It took a little more effort to remove the tub because of corrosion, however, by rocking the tub back and forth I was able to work it free and remove it. I then removed the bolts connecting the Trunnion to the tub. It took a hammer to remove the Trunnion from the tub, once again because of corrosion.

4. After removing the tub, the seal assembly was next and it was easy to remove. I cleaned the agitator shaft with steel wool before beginning the reassembly to remove the corrosion. Before installing the new seal, I lubricated the agitator shaft and the inside of the seal with a silicone grease that is normally used for water faucets. The seal installed easily although care was required to insure that the seal did not twist out of place when sliding it down the agitator shaft.

5. The rest of the reassembly went easily. Since my old filter on the bottom of the tub was clogged, I replaced it with a new one. It took a little time to get every tab on the filter aligned properly so that it could be rotated into place, but it went easily. Everything else reassembled with no problems.

6. It took considerable time to figure out how to replace the drive belt idler arm assembly because I could not figure out how to remove the pin that the idler arm pivots on. I finally reviewed the parts list on-line again and determined that there is a small C-clip that holds it together. Once I knew that. I was able to see the clip and remove it. From that point on, it was very easy to remove the old assembly and reinstall the new one. If I had to do it over again, I would have changed the sleeve at the same time that I changed the idler assembly because the assembly still wobbles on the pin more than I would like. However, it works fine so I won't worry about it until other repairs are needed.

The parts that I ordered from Parts Select were exact matches for the parts that I removed. They were in stock and were shipped the next business day. I would rate the repair as very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-1 of 1