417463-1-M-Frigidaire-131302800-SCREW.jpg
417463-1-S-Frigidaire-131302800-SCREW.jpg 417463-2-S-Frigidaire-131302800-SCREW.jpg 417463-3-S-Frigidaire-131302800-SCREW.jpg

SCREW

PartSelect Number PS417463

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

  • Compare At

    $6.32
  • You Save

    $1.05
  • Your Price

    $5.27
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 6 reviews What's this?
1-6 of 6
 

7 of 10 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers

CustomerEdward from Baltimore MD

Drying too slowly

Removed access plate from back bottom left
Removed belt from motor
Needed to lift up top of dryer
Inserted flathead screwdirver in front under top to push in two metal clips holding top down
Lifted up top of dryer
Removed 2 screws holding on front of dryer
Removed front of dryer
Broke Door Switch removing front of dryer. I should have depressed the metal sides in and pulled switch through hole.
Instead, I tried to remove the leads. This broke the fragile prongs.
Started dryer (with belt removed so drum doesn't spin)
Verified ignightor came on every heating cycle
Gas turned on properly
Gas turned off after 90 seconds
Gas never came back on
Indicitive of bad coils
New coils solved the problem
Replaced door switch and lint trap cover in the process.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

Tools

CustomerGary from Grand Junction CO

Broken / loose vane

Removed broken Vane and reinstalled replacemnet real time repair 2 minutes. It took longer to open box than to fix.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerGlen from Redondo Beach CA

Vane broke off inside drum

Inserted new vane into slots in the drum. I then held the front of the drum while I slid the vane tabs in place by pushing the vane to the back of the drum. Once the vane was in place, I screwed in the screw that came inside the vane kit.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerPhillip from Kabetogama MN

Did'nt heat, dryer squealed very loud

I googled and found parts select, listed model make and found parts diagram, found suspected parts from trouble shooting blog. I read repair stories, people who performed identical repairs, followed their lead, made notes ordered parts and
easily repaired my dryer for a fraction of the cost of replacing dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsSocket set

Customerscott from harrison AR

The dryer was eating my clothes

I took off the front of the dryer where the felt liner was located. Took off the old glide and scraped off the old glue with the razor blade. Took the tube of glue from the package and put glue where the old was and pressed the new felt on the dryer front. I then put it together and waited till morning to do a load of clothes. It works fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerNICOLE from WEST JORDAN UT

Door catch wasn't working and screws in door were loose.

popped the catch in existing hole and replaced the screws

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6