417325-1-S-Frigidaire-131268401         -Remote Style Pump with Motor
417325-1-S-Frigidaire-131268401         -Remote Style Pump with Motor 417325-2-S-Frigidaire-131268401         -Remote Style Pump with Motor 417325-3-S-Frigidaire-131268401         -Remote Style Pump with Motor http://www.partselect.com/Schematics/Frigidaire/SY9CMZMG.gif

Remote Style Pump with Motor

PartSelect Number PS417325

Use this with either a top load or front load washer. This pump has an horizontal mount.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Leaking.
  • Will not drain.
  • Noisy.
  • Compare At

    $75.66
  • You Save

    $12.61
  • Your Price

    $63.05
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 19 reviews What's this?
 

3 of 4 people found this instruction helpful

Parts Used:
  • Remote Style Pump with Motor
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Socket set
Customer: Roberta from Cheshire, CT

Water wasn't pumping out

After pulling $4.50 out of one of the hoses. I found that the fins inside the pump were gone. LOL I purchased another pump from partselect.com and proceded to install it. It was a simple installation, the hardest part was getting the hose clamp off of one of the hoses( it was one of those dang clamps you need a pair of pliers to remove). I switched the mounting brackets from one pump to the new one and reinstalled the pump. Machine was running in under 1/2 hour. Thank you partselect.com

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
  • Remote Style Pump with Motor
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set, Wrench (Adjustable)
Customer: Steven from Gilbert, AZ

Remote drain pump leaking

First, I unplugged the washer then removed the front panel to the washing machine, then the pump cover, then the two hoses connected to the pump, draining them into a small bowl. I removed the ground wire and electrical connections.

Then I removed the two bolts holding down the pump and removed it. I had to pivot the hose connections on the pump to match the old one. Once I did this, I removed the hold-down bracket from the old pump and installed it on the replacement pump.

Getting the hoses clamped back on the new pump was a challenge, and I finally used an automotive clamp on the rear hose. Once the hoses were connected, I bolted the pump back in, reconnected the power and ground connections and replaced the cover.

Overall, it was a fairly straightforward installation and the only challenging part was the hose clamps.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
  • Remote Style Pump with Motor
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Larry from Seminole, OK

Wash water would not drain from tub

Loosened top of washer from spring tabs and leaned it against wall, removed two phillip head screws from the front bottom panel, removed panel. Removed spring clamps from 2 hoses( make sure water is drained from tub before doing this!!) on pump, removed 2 wire connectors. Used nutdriver to remove 2 screws that held down pump. Replaced pump and everything else installs in reverse. Almost forgot, the plate that holds the pump to the bottom of the washing machine has to be removed from the old pump and attached to the new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
  • Remote Style Pump with Motor
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: Richard from kidder, MO

Orginal pump was starting to make excessive noise.Checked out to find a lot of side play in the pump shaft.

ordered the new pump,its a lot more heavy duty than the orginal.had to change the mounting bracket somewhat. the new pump mounted bythe bottom of the pump housing and theold pump mounted by the side of the pump housing. so, wnere the curve was in the mount, I used the bench grinder to cut the curve out to make a flat surface for the new pump to rest in ,also drilled two 1/4 inch holes in the mount for the bolts to mount the pump.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
  • Remote Style Pump with Motor
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Socket set, Wrench (Adjustable)
Customer: Calvin from Nashville, TN

Rusted frozen washer drain pump

Disconnected power, removed hoses, removed housing and pump. Re oriented drain pipes on pump to align with washer hoses (just twist collar and re set) attach foot bracket and secure to washer bottom. Attaching the hoses with the compression clamps was a bit of a problem until I used pliers to press the ends together and then an adjustable wrench to hold them tight. Slid on hoses and released clamps. Replaced electrical and secured pump cover. Done in about 15 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?