Remote Style Pump with Motor

PartSelect Number PS417325

Use this with either a top load or front load washer. This pump has an horizontal mount.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Leaking.
  • Will not drain.
  • Noisy.
  • Compare At

    $73.42
  • You Save

    $12.24
  • Your Price

    $61.18
In Stock
Order within the next 5 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 19 reviews What's this?
1-5 of 19
 

48 of 50 people found this instruction helpful

Parts Used

  • Remote Style Pump with Motor

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerThomas from Walpole, MA

Pump motor failed

First, remove the 2 screws that hold the lower front cover in place, remove the cover and disconnect the plug and the ground wires from the pump. Next attach the washing machine drain hose to a wet vac, since even if the machine is empty, there will still be water in the outer tub and the pump. Suck the whole thing dry, remove the 2 bolts that hold the cover onto the pump, use a pliers to remove the 2 hose clamps, remove the hoses (no mess because of the vacuum). Remove the 2 screws that hold the pump to the base of the washer and remove the pump. Save the mounting bracket from the bottom of the pump. Orient the outlet on the new pump to match your old one if needed, instructions to do this are included with the new pump. Install the mounting bracket onto the new pump. Mount the pump to the washing machine base, reconnect the hoses, the cover and the wiring. Put the drain hose back into your drain. Run the machine, check for function and leaks. If all is well, replace the lower cover. Don't forget to tell your wife that the job was a whole lot harder than it looked.

Help other customers find the most helpful instructions.

Were these instructions helpful?

22 of 24 people found this instruction helpful

Parts Used

  • Remote Style Pump with Motor

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerJames from Blacksburg, VA

Washer wouldn't drain

Vacuum all water possible from the tub. Remove the front panel to provide access to the pump. remove the pump from the washer, but leave the hoses attached lift the pump into the bucket, and remove the clamp from one of the hoses. clip the hose partially off the fitting and drain water from the rest of the tub and hoses. It may be necessary to reattach the hose during this draining process to keep from overflowing the bucket. When the lines are empty, remove the other clamp and remove the hose from the pump. Be sure to disconnect the pump and check the hoses. I have found a sock in the tub drain line twice, which either stopped the line, or blocked the impeller. replacement of the pump is the reverse.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 11 people found this instruction helpful

Parts Used

  • Remote Style Pump with Motor

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Socket set

CustomerRobert from Roswell, GA

Pump leaked

First I turned off the water. Since the pump is at the front of the machine,it was easy to get too. I then removed the hoses by squeezing the hose clamps with pliers. I removed the electrical plug and then removed the 3 screws holding the pump to the base. I changed orientation of the outlets per instructions,which was very easy. Installation of the new pump was performed in reverse. I had difficulty getting one of the hose clamps back on and changed it to a screw clamp. I turned the water on,ran the machine and checked for leaks. Partselect saved me several hundred dollars in repair costs.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

  • Remote Style Pump with Motor

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerVICTOR from THORNTON, CO

No draing water

just change the new pump conected to trhee wires and two pipes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 13 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Socket set

CustomerPaul from Lewiston, ID

Leak in pump seal & cracked drum veins (2)

Very easy - veins are held in with one screw, when removed just slide to front of the washer and lift out. Pump assembly is a remote unit complete with drive motor. Take 2 screws out of the water shield, then unplug power to the pump motor and the green ground wire. Slide a cloth under the machine at the area of the pump to catch the water when the hoses are removed. Remove the hose clamp from the rear of the pump and the clamp on the discharge hose. You may be able th remove the hoses now, but if not remove the two bolts that hold the pump to the washer base & then remove the hoses. When you have the pump out you have to change the mounting base to the new pump. Also you may have to rotate the new pump discharge side with the motor (instructions are included with the new pump) - mount new pump, attach hoses, clamps,wires and water cover. Install front door that was removed at the start - pump in in the front right corner after removing the access door in front.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 19