402231-1-M-Whirlpool-9742946-Wash-Arm-Bearing-Ring.jpg
402231-1-S-Whirlpool-9742946-Wash-Arm-Bearing-Ring.jpg 402231-2-S-Whirlpool-9742946-Wash-Arm-Bearing-Ring.jpg

Wash Arm Bearing Ring

PartSelect Number PS402231

This part will fit between the newer type lower wash arm and the wash arm retainer nut of your dishwasher.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not cleaning properly.
  • Leaking water.
  • Unusual Noise.
  • Not draining.
  • Compare At

    $4.51
  • You Save

    $.75
  • Your Price

    $3.76
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 89 reviews What's this?
76-89 of 89
 

0 of 1 people found this instruction helpful

Parts Used

  • Wash Arm Bearing Ring

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerRobert from West St. Paul MN

Plastic bearing was worn out, in two pieces

Removed center screw, lift up the wash arm, remove the plastic bearing. Line up and insert new bearing put the wash arm back in place on top of bearing. Insert screw and tighten. Done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerKevin from Budd Lake NJ

The bottom sprayer was broken,upper sprayer was broken.

Part selection was very easy with the detailed diagram that was provided on the website.The diagram was also very helpful in the instalation. The bottom sprayer neeeded a new bushing and "wing nut"; very easy to install less than 5 mimutes. The top sprayer needed to be unscrewed and replaced with the new assembly. Less than 10 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJohn A from Ocala FL

Tube to upper spray arm missing

Check your card against your invoice. They added an extra 1.53 dollars that wasn't on my invoice.

Their is really nothing to explain.

1. Upper Spray arm It's just removed 2 screws and replaced the old with the new.

2. Lower spray arm bearing and seal, Removed center wing bolt, removed arm removed and replaced seal and bearing.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Wash Arm Bearing Ring

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerRobert from Smithfield RI

Water was coming out of the door.

I removed the bolt that holds on the bottom sprayer, removed the worn bushing, replaced the bushing, reinstalled the sprayer and tightened the bolt. It was that quick and easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerAlan from Freehold NJ

Lower dish sprayer came off, retainer nut broke.

Simply looked at the exploded parts diagram and put it back together 1-2-3. No problem!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerGary from Danville IL

Dishwasher made a squeaking sound when running

The problem was the water powered lower swing arm bearing (bushing) had worn out (had rubbed away part of it's flat surface). First I removed the large screw with the big flat finger grip flanges on the top side of the lower swing arm assembly. this assemble looks like a big hub cap. Lift the assemble up and off the attachment stem. The bearing goes on top and the seal on the bottom. Both just push in place with your fingers. Reinstall the assemble on the attaching pivot point that it was removed from and secure with the large thumb screw first removed. Spin the assembley to check for any binding. Do not over tighten the thumb screw. Water pressure is all that drives this assembly and it should always turn with no obstructions.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerGeorge from Carrollton TX

Wash arm retainer nutt broke

First I ordered the correct parts. The repair involved removing Wash Spray Arm inserting the Lower Spray Arm Seal, peplacing the Wash Spray Arm, then inserting Wash Spray Arm Bearing Ring, the inserting and hand tightening Wash Spray Arm Retainer Nut.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

Tools

CustomerLynda from Syracuse NY

Dishes weren't getting clean

After looking at the sprayarm, changing detergents and washing every speck off the dishes only to have them come out dirty I decided to replace the sprayarm seal and bearing ring. I didn't really need the sprayarm seal, but figured I had come that far I may as well. It went really well and now I have clean dishes. I spent $26 on parts but a service call is $70 and I still would have had to replace the parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Wash Arm Bearing Ring

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJames M from Dayton OH

Bearing righ had worn out

unscred by hand wash arm are removed old bearing ring, replaced it and re assembled the wash arm.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJack from Belvedere IL

Retainer nut broke

Thanks for the quick survice. The part came in two days. I looked all over town for 4 days for the same part. We will use you site from now on for all of our repairs. All I had to do was screw the new parts inplace ,and we were up and running.
Thanks
Jack & Sue

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJoe from Augusta GA

Wash arm retainer nut was broken

I took the old Wash arm retainer nut out and put the new Wash arm bearing ring and Nut in place and hand tightened. It was fixed in less than a minute. Parts were perfect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJoseph from Spokane WA

Washing poorly, irregular noise in wash cycle

I removed the old parts and replaced them with new parts. It failed to solve the problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsWrench(Adjustable)

CustomerJudy from Arlington TX

Wouldn't wash

Called my son in law and he did it

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 3 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers, Wrench set

CustomerDavid from Hernando MS

Leaking dishwasher

Installed all parts. Dish washer still leaks. Wasted my time and money.

Help other customers find the most helpful instructions.

Were these instructions helpful?

76-89 of 89