401674-1-S-Whirlpool-9704291           -Dome and Blade Assembly
401674-1-S-Whirlpool-9704291           -Dome and Blade Assembly 401674-2-S-Whirlpool-9704291           -Dome and Blade Assembly 401674-3-S-Whirlpool-9704291           -Dome and Blade Assembly

Dome and Blade Assembly

PartSelect Number PS401674

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Touchpad does not respond.
  • Compare At

    $29.29
  • You Save

    $4.88
  • Your Price

    $24.41
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 6 reviews What's this?
1-6 of 6
 

39 of 46 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerLynda from Boise ID

Drive coupling on blender shattered

The drive coupling on my Kitchen Aid Blender shattered into dozens of pieces. Found this website and realized I could buy a new one. Could not remove coupling base with "official" instructions. However, user comments on how they removed coupling base very helpfull. Put thin blade screw driver thru hole on bottom of blender base, held the blade from turning and twisted the coupling base off. Very easy and quick. New one when on just as easily.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 15 people found this instruction helpful

Parts Used

  • Dome and Blade Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerLevi from Blue Grass IA

Shaft in blade assembly sheared

part does not fit this model like it claimed it did. Blade assembly was too small in diameter. This part will cost more to send back for refund. Part did not work. Blender still broken.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 18 people found this instruction helpful

Parts Used

  • Dome and Blade Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerNora from Lodi OH

Blade wouldn't rotate

All I had to do was replace the part! Service was excellent! Ordered the part and had it the next day and my blender was up and running!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

Tools

CustomerMary Lea from Chadron NE

Drive coupling chewed up by blade assembly

KitchenAid Blender: The directions said to use a screw driver to pry off the old drive coupling, and then clean out any remaining broken pieces. The drive coupling screws on so that did not make sense to me. I called KitchenAid and they gave me a number of the closest KitchenAid dealer. I was told that I needed to be careful not to bend the drive shaft; I would need to find some way to secure the drive shaft from turning while unscrewing (a reverse screw) the drive coupling. Find the appropriate size thin ignition wrench. Remove the old coupling and screw on the new coupling.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 9 people found this instruction helpful

Parts Used

  • Dome and Blade Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerPAUL from LAWRENCE KS

Blades on blender locked up

Piece of cake. Part was expensive and shipping likewise. Very fast

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 18 people found this instruction helpful

Parts Used

  • Dome and Blade Assembly

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerDAVID from GLEN MILLS PA

Slow, intermittant discharge

First I disconnected the washer and used a shop vac to suck out remaining water throught the effluent tube. I then pulled the washer out from the wall and opened up the panel in the back where I saw a penney in the baffeled catch basin and, a wad of lint wrapped around what looked like three 7" wires.I opened up the top with the putty knife and flipped it bacl. I then proceded to remove the top sections of the tub (soap/bleach dispenser, etc) Then I removed the dome using a stubby screwdriver to 'pop' the internal catches. The next thing to come out was the perforated baffel. I could see the blockage through the drain holes in the bottom of the tub. I made a hook out of a coat hanger to extract the wad and 'wires'. Also, a pair of needle nose plires were used to pull the wires through the tub holes. Rhe unit was then re-assembled and has worked fine since.

The 'wires', it turned out, were identified by my wife as the wires from some of her UNDERWIRE BRAS! They will get handwashed henceforth!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6