Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS398589
This kit is used for trash compactors. It includes both gears, pin spring, C-ring, ram stop, and ram cam.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Moved the compactor out from under cabinet and unplugged the powercable.Laid compactor over on its side Removed the top (4 screws) and base plate (3 screws) as well as the coverplate for the motor(3 screws)Found that large drive was broken in half. Used two screwdrivers to start split ring then pliers to pull it off the rest of the way.Removed the drive gear and the washer. Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Replaced the gear and unit worked execpt the plunger hit the side of the garbage container. This appears the be the reason the gear broke in the first place. Defective assembly from the factory. To correct I had to remove the newly installed gear system remove inside cardboard side cover, Remove the screws that hold the bearing for the lift screw so I could remove the chain. After removing the chain I could adjust the plunger to be level and not hit the side of the garbage container on its way down.
Moved the compactor out from under cabinet, laid it on it's side, removed bottom casing (two nuts front, three back), remove compression pin from small drive gear shart, replace new small drive gear and install compression pin, loosen motor mounts to allow large gear replacement, remove circlip holding large drive gear to shaft, remove and repace damaged gear, set gear clearance and tighten motor mounts, grease gears, replace bottom casing. .
Took the under housing off to see the drive gear. It had broken in half. (Exactly like one of the suggestions said). Replaced the drive gear and re-assembled. It worked great!Thanks.
Trash compactor started making "bumping" sounds when the RAM went through a cycle and tried to come back up. Finally, one day heard a "pop" went the RAM traveled to the bottom. The gear broke in half. Purchased the gear parts "KIT" online and repair took 15 minutes. Easy to do. Unfortunately, this was not only problem. The "cause" of the gear breaking was the Momentary Start/Stop Switch was bad. It's failure led to the main switch not working. The unit could not tell when the RAM had reached the top of it's cycle. The other problem was that I didn't put trash in the compactor. Suggest HIGHLY to never operate the unit's RAM mechanism without the compactor being at least 1/2 full per the instruction manual. Running it empty can cause a major problem, such as the gear breaking/stripping.
Unplugged trash compactor and removed from undercounter. Took cover off and removed broken plastic gear. Replaced with new gear and put cover back on
First i removed 2 screws that holds it to the cabinet,pulled the unit out removed the cover off the bottom of the unit,then i notice the gears were damaged,but was not supprised,because the machine gets over worked.Then i removed one clip,removed one gear,the other gear had a pin,tapped the pin out with a punch ,pulled that gear off.then replaced both gears .Got it back together and it now works like new.i am very pleased with your service,you responded right away and let me know the order had filled.i ordered it on sunday night and i recieved it on tuesday morning .i will surly use your service in the future you guys are great. thanks alot
Unscrew the bottom, pull out the chain, replace the gear.
Simply removed the two plastic gears (held on by some sort of clip), put the new gears in place using the spacing instructions that were provided in the kit ....... and it is working!
First thing I did was put the unit on its side and removed the bottom to access the broken plastic gear that moves the chain that drives the compactor up and down...There I was able to manually move the chain by turning the nut with pliers and moving the piston up (painfully slow) until I could at least use the bin for trash while I waited for the replacement part to arrive. Once I had the part I loosened the four bolts that allowed the drive gear to move a little and slacken the chain - I then put in the new gear - make sure you have the proper spacing and washers - my replacement kit didn't have any washers so I resused the old washers and all seems to be working well!
The plastic drive gear broke and the unit was locked in the down position. The repair kit contained all of the parts required to fix the problem plus other replacement parts for the gear drive unit. It was very easy (about 20 min.) to replace the gear and other parts. The unit works fine now.
With nothing in the KitchenAid Instructions nor anything on the internet… I had to go it alone.Actually quite simple… I laid the unit over on its front and removed the 5 screws holding on the bottom plate. This exposed the motor and drive train which turns the two compacting screws on each side. The main drive gear was broken.Taking a wrench to the main drive… I was able to free up the jam… a piece of glass from a broken bottle.I went to the internet and did a search on KitchenAid Trash Compactor Parts and discovered PartSelect.com… They had me enter the Model Number of my unit and a parts diagram and list came up… I found the gear I needed… ordered it and in two days it was here. Instructions came with the gear on replacement and in no time I was back in business.I was impressed with the simplicity of KitchenAid’s Compactor, and the ease in which I was able to get my part from PartSelect.com!
I flipped this unit over,removed 4 screws to the drive gear.I tore apart found a nut came off the screw rod.Which broke the drive gear.I looked on line found the parts select page.That showed the diagram i needed,to order parts, i needed.The wife and i tackled this task,of repairing this product.The repair was quick and easy.It took less than 30 minutes including cleanup.The wife happy,that all that matters.Jack
pulled it out, turned it upside down, and removed the gear, then replaced it, turned it back up and pushed it back it worked.
Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.