395284-1-S-Whirlpool-833697            -Condenser Fan Motor Kit
395284-1-S-Whirlpool-833697            -Condenser Fan Motor Kit 395284-2-S-Whirlpool-833697            -Condenser Fan Motor Kit http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/14290.gif

Condenser Fan Motor Kit

PartSelect Number PS395284

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Freezer section too warm.
  • Noisy.
  • Fridge too warm.
  • Fridge runs too long.
  • Will Not Start.
  • Compare At

    $56.42
  • You Save

    $9.40
  • Your Price

    $47.02
In Stock
Order within the next 9 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Condenser Fan Blade

Part Number 1672384

$20.10
No Longer Available

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 34 reviews What's this?
1-5 of 34
 

117 of 125 people found this instruction helpful

Parts Used

  • Condenser Fan Motor Kit

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerTom from Franklin, WI

Sometimes the condenser fan would start causing the refrigerator to overheat.

Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire about two inches from the fan.
Cut and strip the new wire. I cut the new wire in half (about 6 inches.) Connect the two wires, twist and used 2 wire nuts. Tie wrap the wire to the wire harness. Mount the new fan (three screws)
Screw the back panel back on.
Mount the new

Help other customers find the most helpful instructions.

Were these instructions helpful?

24 of 27 people found this instruction helpful

Parts Used

  • Condenser Fan Motor Kit

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Socket set

Customerrobert from nashotah, WI

Noisy fan motor

rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse panel. ( 20m). i also took time to clean grilles with small vac and damp rag, ( looks and sounds like new) bob Wi.

Help other customers find the most helpful instructions.

Were these instructions helpful?

20 of 25 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

Customerfrankie from pelham, TN

Freezer quit freezing -fan motor quit and the water froze like a frozen waterfall and didn't make enough ice cubes.

First I unplug the refrigerator, then I unscrewed the cardbord cover with a screwdriver, disconnected the wires, unscrewed the screws, removed fan bracket with the fan. Since my wire connector was different, I had to strip the wires to connect the fan, twist wires together with the connecting wires, use wire nuts wire nuts and wrapped in black tape. I then hooked together the connection making sure the fan was rotating in the right direction. I then placed the fan bracket back in its place, lined up the screwed holes and installed the screws back to the original tightness. I plugged the refrigerator up to see if the fan was working properly. It was so I unplugged it again to start the nwxt part replacement.
The next part I installed was a icemaker and water dispenser water inlet valve. I turned off the incoming water valve. I removed the two screws that held the old water valve in place. Unplugged the two connectors, removed the water lines and reinstalled the new water inlet valve hooking it up the way I unhooked it. Then I turned on incoming water line, checked for leaks. I put the cardboard panel back on and was done. The two parts were successfully installed in an hour. We now have a efficiently working refrigerator and a cold freezer and have the proper amount of ice cubes that are supposed to be made.

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 23 people found this instruction helpful

Parts Used

  • Condenser Fan Motor Kit

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerFlorentino from Windsor Locks, CT

Refrigerator stopped cooling. Pulled it out of the alcove and plugged it back in. Compressor starfted but noticed condenser fan was not turning. Unplugged fridge and tried to turn the fan by hand - frozen.

Remove the back hardboard cover screws for access to the condenser fan. I opted to tip the fridge over on its side for even better access to the fan mounts and wire. Replaced the fan assy (reused the fan). Splice the wire and it's done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 17 people found this instruction helpful

Parts Used

  • Condenser Fan Motor Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsSocket set, Wrench set

CustomerBob from Hesston, KS

The old motor wouldn't turn the fan.

After moving the refrigerator away from the wall I removed the cover on the lower back of the unit by removing the screws that held it in place. The condenser fan was not turning and there was heat build up in the area causing the refrigerator to not work properly creating elevated temperatures in both the freezer and regrigerator. Removal of three torx screws from the original motor was all it took to get the motor free. By turining it and working the fan blade around the mounting bracket I had the motor out in just a few minutes. Replacing the new motor was just as easy to reinstall. The fan was removed from the old motor and placed on the new for installation. The original motor was wired to accept a connector from the wiring harness of the refrigerator. I simply cut the connector off the wiring harness and stripped the insulation from the wires which easily allowed me to connet the wires of the motor and harness with two wire nuts. Three self tapping screws were used to hold the motor in place replacing the torx screws. Installed I plugged the unit in and immediately the fan started spinning as the unit came to life. Cleaned and replaced the cover over the back and slid back into its spot. Running as good as it did when it was new. Easy job to take care of.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 34