395284-1-S-Whirlpool-833697            -Condenser Fan Motor Kit
395284-1-S-Whirlpool-833697            -Condenser Fan Motor Kit 395284-2-S-Whirlpool-833697            -Condenser Fan Motor Kit http://www.partselect.com/Schematics/Maytag/14290.gif

Condenser Fan Motor Kit

PartSelect Number PS395284

Manufacturer Part Number 833697
Manufactured by Whirlpool

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a mounting nut for the blade and a cushion. This part provides forced-air cooling for the condenser coil.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Freezer section too warm.
  • Noisy.
  • Fridge too warm.
  • Fridge runs too long.
  • Will Not Start.
  • Compare At

    $46.44
  • You Save

    $7.74
  • Your Price

    $38.70
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Condenser Fan Blade

Part Number 1672384

$20.25
No Longer Available

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 34 reviews What's this?
 

8 of 10 people found this instruction helpful

Parts Used:
  • Condenser Fan Motor Kit
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: JAMES from Middleboro, MA

Freezer cooling problems - would get too warm then too cold. Condenser fan would run sometime but not always

Unplug
Remove entire back panel (both chipboard and metal fan grill)
Unscrew both fan mount plate screws - fan won't be able to come out because it is still plugged in
When looking at back of fridge, locate a small plastic box to the immediate left of the condenser. It's a circuit block. Release the metal spring clip holding the plastic cover in place, and trace the fan wire connections back to the fan. Make a note of which wire is connected to which terminal (1 of the fan wires has white lettering and 1 is just black)
Unplug both fan wire connects from circuit block to release the fan power cable.
Remove the fan mounting plate
Release fan blade clip by pressing fan against motor and unscrewing and remove fan blades
Unscrew motor from brackets - note alignment of motor on brackets
Mount new motor on brackets. Leave plug wire disconnected (replacement motor has a harnessed plug wire)
Connect new plug wire to the circuit block keeping wires connected to the proper terminals
Snake new plug wire behind condenser like the old wire was and run through cable bracket to the back right of the condenser
Plug wire harness into motor and re-mount fan mount plate
Reattach fan blade and secure using blade mount kit
Replace back panels

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 13 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Wrench (Adjustable)
Customer: Jose from Gilbert, AZ

Refrigerator fan was not fast enough

My refrigerator condenser fan was burned out, and it was so weak you could stop it with your hands, and over time it will stop working.
I order a replacement and change it my self, all you got to do is take the cover from the back off and unscrew the fan + blade it was like 3 screws; I did had to cut the wires because the original fan had a connector the replacement did not had, but that was no biggie, it all works now it's been over a week so I call it a success.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used:
  • Condenser Fan Motor Kit
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: W from Nellysford, VA

Freezer too warm; noticed sides of refrigertor were warm

I saw on a partselect web site that these symptoms could be caused by a failed condensor fan motor. After removing the cardboard panel in back of the refrigerator I noticed the fan was not running when the rfigerator was. The fan was held in place by three brackets. I unscrewed the screws holding the fan motor to the brackets and also unscrewed one of the brackets to make room to pull the motor out. I cut the wires close to the motor. I removed the fan blade and secured it to the new motor. I had to reroute the old wires in order to have enough slack to use wire nuts to attach them to the leads on the new motor. I then re-attached the motor to the two brackets remaining in place and then re-attacehed the third bracket I had removed to get the motor out.. The most difficult part was working in a very confined space.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used:
  • Condenser Fan Motor Kit
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Socket set
Customer: David from Choctaw, OK

Freezer will not freeze or cool the ice box

I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used:
  • Condenser Fan Motor Kit
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Steven from Brigham City, UT

Condenser fan stopped working

1. Removed the cardboard cover.
2. Removed the terminal block and unplugged the old motor.
3. Removed three screws that held old motor to the bracket.
4. Removed the fan blade from the old motor.
5. Installed the fan blade (after cleaning) to the new motor.
6. Crimped on new wire terminals onto the leads on the new motor.
7. Installed the new motor using the fasteners provided.
8. Plugged the new motor wires onto the proper terminals in the terminal block.
9. remounted the terminal block.
10. reinstalled the cardboard cover.

Help other customers find the most helpful instructions.

Were these instructions helpful?