393669-1-M-Whirlpool-8273062-Igniter-Screw.jpg
393669-1-S-Whirlpool-8273062-Igniter-Screw.jpg 393669-2-S-Whirlpool-8273062-Igniter-Screw.jpg 393669-3-S-Whirlpool-8273062-Igniter-Screw.jpg

Igniter Screw

PartSelect Number PS393669

This screw is sold individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $3.24
  • You Save

    $.54
  • Your Price

    $2.70
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Surface Burner Spark Igniter

Part Number 650811

This part helps your burner ignite and produce flame.

$13.02
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 3 reviews What's this?
1-3 of 3
 

10 of 10 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerDidier from LONE TREE CO

Ignitor did not work

- Removed the cover.
- Removed te two Torx screws.
- Pulled the burner a couple of inches to be able to disconnect the wire.
- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.
- Treated all screws with a high temperature copper paste to prevent oxidation.
Installed the new ignitor with the new screw.
- Reconnected the wire.
- Installed the two Torx screws.
- Voila, it works.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

Customernhung from chesapeake VA

Two igniters didnt function and it continued to spark after the gas ignited.

Well, after I finally got the parts, the repair was easier than anticipated. You deffinitely want to lift the unit out to replace the spark module and swap over one wire at a time so you dont forget where they go, (important on a gas stove) When I pulled out the old unit I found it was just jammed in there when constructed, I expected more from Jenn-air, and the plastic casing was broke and pulled apart. Surprised it lasted this long. Also three of the ceramic insulators on the ignitors were broke or cracked. But over all the unit was fairly simple to repair if you take your time and practice safety. Remember, you are working with gas and electicity, and use soapy water to check your connection when you reconnect the gas line. Dont try to work on it still hooked up and in its mount . Disconnect it and lift it out.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customercalvin from Edmond OK

Electrode broke, screw broke

The ceramic on the electrode broke due to water over boiling the week of Thanksgiving. When i tried to loosen the screw to replace the electrode it broke off inside the threads. Ordered whole new unit overnight. Back in business in five minutes. Thanksgiving was back on!! Thanks!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3