392943-1-S-Whirlpool-8268395           -Pump Sump Gasket
392943-1-S-Whirlpool-8268395           -Pump Sump Gasket 392943-2-S-Whirlpool-8268395           -Pump Sump Gasket http://www.partselect.com/Schematics/Whirlpool/BSH9UH7I.gif

Pump Sump Gasket

PartSelect Number PS392943

This gasket goes around the perimeter of the main pump sump. This part is also sold in a kit with the sump.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Not cleaning dishes properly.
  • Compare At

  • You Save

  • Your Price

In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Sump with Gasket

Part Number 973485

As per the factory, the hole for the thermistor should be 31-31.5mm. This works in conjunction with the pump and filtration system. It is used to receive drainage for disposal.

In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.5 / 5.0, 3 reviews What's this?
1-3 of 3

19 of 27 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: Phil from Fairfax, VA

Water was leaking.

This unit was unique that whole motor assembly was held in its place by two plastic clip. The gasket had few rings that worked as place holder, although gaskets don't go bad often this model could be if it gets pulled alot and if motor assembly get pushed it will push up the gasket and cause a leak. Repair was simple, 1) take spray arm off from inside. 2) get under neath the dishwasher, take off wires so it would free up some room, pulled two plastic holder out, gently push the motor assembly up to the tub, 3) from inside the tub, pull up the assembly enough to get your hand under the gasket and pull them off. 4) Replace the gasket, align the assmebly and push down to snap in the gasket. 5) get under and push in two plastic clip back in, put wires back into its place. Back in the tub to push down the assembly again to make sure there are flush with surface. Put spray arm back on. Finished.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 17 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Pliers
Customer: Dale from Oldsmar, FL

Chopper not performing

I noticed some residue in the dishwasher so I decided to clean the chopper screen. I dismantled the screen and spray assemblies and removed the chopper. The chopper was extremely worn and the chopper washer/gasket was missing. I reassembled the parts I removed and as I was placing the screws in the screen assembly I dropped a screw into the impeller well. Since the screws are stainless I was forced to remove the whole motor assembly. Since I had to order a chopper I went ahead and ordered a motor assembly gasket for reassembly. The mistake I made was not ordering a drain valve at the same time for when I removed the valve to clean it the rubber separated. The dishwasher will not function without it. This is where PartsSelect really came through for me. The 2-3 day shipping came in 2 days and the drain valve which was really going to hold me up with standard shipping came the very next day! Way to go PartsSelect! Everything went back together just fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 8 people found this instruction helpful

Parts Used:
  • Pump Sump Gasket
Level of Difficulty: Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: jim from kennett square, PA

Black specs on dishes

Found the gasket to be wearing out. Once I got the part I took everything apart inside to find that I could have just taken the dishwasher out and replaced from the bottom. It was not difficult, but I've installed a ton of dishwashers. For the average homeowner, this is can be a difficult job since it requires plumbing and electrical skills.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3