| |
17 of 19 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsSocket set, Wrench(Adjustable)
Customereric from Boulder CO
Belt wheel was broken at axle. Terrible noise.
Removed the top and back of dryer with screw socket. It was quite easy. Then, I removed the broken wheel by releasing the tension spring. I replaced the wheel. The toughest part was re-threading the belt. But, even that was simple. The dryer runs smoothly and quietly again!
|
13 of 16 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerSusan from Glen Ellyn IL
Plastic knob cracked off machine
It was super easy...as the knob (Part No. 18 on our Whirlpool Duet Dryer) broke off cleanly leaving the metal pin exposed....(we had been turning it with pilers in the interim) so I just popped the new knob on and we were good to go! It was really easy to do and easy to locate the necessary part on your site. I won't hesitate to use your company and website again. Thank you for making all the parts available and saving us a service call!
|
8 of 12 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerDonnette from Fresno CA
Cracked burner know
If you remove knob and sleeve remains, you have to use needle nose pliers to remove. Pull straight up, don't wiggle back-and-forth too much. If you put too much pressure on glass-top, it can crack. Prying is DANGEROUS on glass-top stoves.
|
7 of 10 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
Tools
CustomerTheodore from Mastic Beach NY
Broken control knob,damaged printed ckt.In control.
Removed top panel from machine(3 screws,access to rear was necessary),removed detergent dispenser to access screw for control panel,removed control knob and unfastened control panel,disconnected harness from ECU,unfastened harness from retaining clips,removed control panel&uncliped circuit board assy.from panel,transferred buttons to new ckt.board assy,reassrmbled control panel&reinstalled,routed harness,installed new knob,verified operation,reinstalled top panel&dispenser.
|
4 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRichard from Tempe AZ
The knob that controls the wash setting broke
It only took a few seconds to slide on the new knob after it arrived by UPS. The part arrived sooner than scheduled. Great service and product.
|
4 of 6 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerBill from Chanute KS
Control knob broke
I removed the old control knob by pulling it off and installed the new one. Your service was great!
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
Tools
Customerlinval from raleigh NC
Broken door handle
removing the old srews was a little difficult but once it was done it was much easier to replace the new product.
|
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerGail A from Cave Creek AZ
The plastic control knob to set the washing cycle split in two
slip the knob onto the exposed axel that selects the cycles
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerPatricia from Brentwood TN
Control knob broke - because entirely plastic, turning interior metal selection rod
Pulled off the broken knob. Fairly disgusted with Whirlpool for not bothering to put a metal / aluminum sleeve inside to avoid the exact breakage I experienced. Part Select, however, had the part, got it to me exactly in the time frame I asked for and it was the correct part. I would definitely use Prat Select for any such need.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRenaldia from Cornelius NC
Knob broke off
easy as pie - ordered part. arrived in a few days and popped it back on. easy as pie. great service, quick! will definitely return to buy other parts!!!
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
Customerrichard from Coral Springs FL
Knob interior broke
pulled old broken knob off and removed metal clasp on knob stem. Then pushed new knob on in seconds and worked fine. Of course wife was inpressed just complained about the knob color, but can't do everything perfect!
|