391621-1-S-Whirlpool-8181850           -Bellow
391621-1-S-Whirlpool-8181850           -Bellow 391621-2-S-Whirlpool-8181850           -Bellow

Bellow

PartSelect Number PS391621

Manufacturer Part Number 8181850
Manufactured by Whirlpool

Also known as a door boot seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking water.
  • Compare At

    $127.79
  • You Save

    $21.30
  • Your Price

    $106.49
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 5 reviews What's this?
1-5 of 5
 

24 of 36 people found this instruction helpful

Parts Used

  • Bellow

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerBruce from Tucson AZ

Bellow torn on he3t kenmore

Take off 3 screws at back of top panel and remove. Remove screw to the left of the soap dispenser and push tab on the right inside the machine to remove control panel and lay the panel on top of the machine without disconnecting. Remove 3 screws on the bottom to remove the bottom panel. You have to pull a bit hard to get it off. Remove 3 screws to push through the door lattch and safety switch. Push the window washer nozzle head through the bellow along with the soap feed nozzle.Remove the retainer wire/spring from the bellow where it attaches to the middle panel/inlet. Remove two screws at the top of the middle panel and two screws on the bottom to remove the middle panel with door attached. Loosen the retainer strap ( a large hose clamp) which anchors the bellow to the tub. Remove the plastic nozzle from the window wash hose and mount it in the new bellow. I couldn't get the plastic retainer washer off the nozzle but managed to seat the bello between the washer and the nozzle anyway. Connect the hoze to the nozzle making sure it's pointed in the correct direction. Pull the oblong soap dispenser nozzle into the corresponding bello opening. Seat the bellow around the internal tub opening and place the large hose type clamp, after unthreading it, around the bellow and tighten. Install the middle panel and attach the door latch and safety switch. Now seat the front part of the bellow to the middle panel and attach the retainer hoop/spring. This is a little tricky. I moistened the front rim of the bellow so the hoop would slide over the edge better. You have to stretch the spring to get it to seat properly. Having experience changing bicycle tires helps. Then install the control panel and other panels.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 14 people found this instruction helpful

Parts Used

  • Bellow

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

Customerdavid from Goose Creek SC

Bellow was ripped at the fold, leaking water into the casing.

Removed the top panel. Removed the control panel (one screw behind the detergent drawer). Removed the three screws that held the door latch and switch (pushed it through). Removed the spring-loaded wire that fastens the boot to the door panel(look very closely around the bellow around the opening for the door). Removed the four screws at each corner of the front panel and removed the panel (door still intact). Loosened the band clamp that holds the bellow to the tub. Removed the vent tube from the old bellow and installed on the new bellow. Installation is the reverse of the removal. One tip: when installing the spring-loaded wire around the door panel opening, use several small (padded end) spring clamps to hold the wire in place as you install the wire. If you do not, the areas that you have installed will come undone. Be sure to be careful and use padded ends so that you lessen the likelihood of puching a hole in the new bellow.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 25 people found this instruction helpful

Parts Used

  • Bellow

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerDan from Hudson WI

Rubber gasket (bellow) door seal "worn" out

Have to remove the front two sections of the washer and top- I had to remove the control panel too. POS kenmore gasket failed after about 2.5-3 years. Old gasket got holes in it - If you have a HE3 or HE4 model- look for it! you will get them too!!! Guaranteed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 13 people found this instruction helpful

Parts Used

  • Bellow

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJacek from San Diego CA

Water leak through bellow next to the washer door

simple removal of few screws holding the washer panels and replacing bellow. 20 minutes to complete entire job. Kenmore mechanical washer design is very simple so all components access is very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 11 people found this instruction helpful

Parts Used

  • Bellow

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerTodd from Warsaw IN

The bellow leaked

make sure to take the front shield off... the job will go much smoother!...

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5