Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS389114
This kit contains one clip, a screw, and a nut.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Drilled out old and broken hold down clips, installed new ones(4). Cut old wires attached to surface plug in block, striped wires, and attached new plugin kit(4), warmed up heat shrink with a hair dryer, put in new drip bowels, the stove is like new. I ordered the parts on line early one morning, the next day they were at my door and installed that day, everything that I ordered was there, and fit properly. Way to go Part Select.com Jon
Help other customers find the most helpful instructions.
Were these instructions helpful?
Pulled out the electric element from the range, replaced the new drip bowl on three of the burners and then replaced the electric element pushing it into the hold down clip. On the fourth burner, I removed the electric outlet, the previous incorrect drip bowl and had to drill out the broke off hold down clip that was no longer there. Next I placed the new hold down clip in position, alligned and fed the little screw through the hold down clip. I used a vice grip to hold the nut in place and with a screw driver tighened the nut. I placed the drip bowl in place, attached the electric element and slipped it into the new hold down clip. Everything went smoothly and I experienced an excellent repair job. We received prompt service and had no problems. I just hope the used appliance that we bought works now. It looks great. It is for a rental unit.
I followed the instructions on removing the existing burner, recepticle, and section of wire. Then followed same instructions for reinstalling above new parts. The instructions were simple and straight forward. The only gluich was that I had to drill out the rivets holding in the old hold down clips. I drilled these out with an 1/8" bit on the burner side off the opening.
Started out removing the old clip that didnt hold burner element down anymore. It was a bit rough, since i was taking off a rivet. I used the screwdriver to carefully wedge the edges of the rivet upward so that i could get the wire cutters underneath it enough to snap the head off. After some fanagling for about 20 minutes, i popped it off. The rest of the repair went like cake, and i am soooo thankful that the replacement part i ordered from you included a screw and a nut. Next time, if there is a next time, this repair could be done in 2 minutes. THANK YOU FOR SAVING THANKSGIVING AND A $100 REPAIRMAN SERVICE COST FOR A $10 PART!!!
I removed surface burner and drip pan from stove. Then drilled out the remaining part of the old stabilizer clip. Once clip was removed I installed the new stabilizer clip with the screw and nut that came with the clip. Then I placed the drip pan back into position and installed the burner and locked it into the new clip.
lifted up burner and pulled it free from its connection, then removed drip pan. used my cordless drill to drill out broken stabilizer clip. cleaned up chips from the drill process before installing new clip. installed clip with enclosed screw and nut. I then installed the new burner by lining it up with the connection under the cook top pushed it place and lowered it into the stabilizer clip. Then I turned the burner on to try it out, but I waited for about one hour before turning on the burner because it was cold from being outside.
I had to remove the original clips (broken or damaged). This was the hardest part -- the clips were held on by rivets (not screws), so I had to pound/punch them out (using care so not to damage the stove top). Once I punched the rivet out all that remained was a small hole, I just used the small nut and bolt that came with my stablizer clip kit and mounted the new clips. Everything worked out fine.
Pulled out the stove and unplugged. Removed the back of the oven and removed the element connections. Removed the two screws holding the element in place and installed the new one.Removed the remaining parts of the old clips and installed the new ones. Very easy
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.