Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS388034
These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
The agitator kit is most commonly used if the top part of the agitator is not moving correctly but the bottom is. This kit now includes all pieces shown in photo plus the thrust spacer, inner cap seal and washer. May need agitator grease for repair.
This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. This is the retaining ring for inside of agitator. May need agitator grease for repair.
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
Pop off fabric soft. dispenser with screwdriver in the slot.Remove the plastic seal with o-ring w/ pliers.Remove agitator assy. with 3/8 socket on extension.Pull up/off top agitator, holding on to the bottom agitator.R and R the thrust washer between agitators, w/silicon top and bottom.Remove black sleeve on cam and replace cogs in correct position.Replace agitator and insert cam lined up with tabs and slots, push down firmly to engage tabs. Replace bolt and tighten. Insert seal w/ o-ring coated with soap and push down to groove.Replace softener reservoir.Check out the video.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Watched the great parts select video and then check all other parts on bottom and top agitator for wear then found the parts I needed, very easy fix and runs like new.
got the parts from parts select and got the machine repaired quicklywhat a savingsrepair man would have been over 100 dollarsthe shipping was more than the parts but I saved greatly with no repairmanlove your site and the great savingsi really loved my washing machine and hating to lose itwas so satisfied that I could save it after all these yearsthanks
repair was really simple. If you can get it apart, you can fix it. the parts fit perfectly.
Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.PS Received parts in 72 hours. $10.00 bucks and never left the house.
With the help of a You Tube video, which was watched first, then when the parts were delivered, the video was watched again, then we played the video back and paused it after each section was done so we could make sure we were doing the repair correct. The one thing I will mention that the video doesn't mention to do is, before taking the agitator out of the washer, put a mark somewhere on the agitator to tell you which end is the top. Just remember that the top( cap ) will be off, so that will not work. Otherwise it was a good, easy fix
Washer stopped agitating. I removed the clothes softener cup on top of the agitator by grasping and pulling up, inside the agitator I removed the inner plastic cap by grasping the 2 finger tabs and pulling up. There was a plastic retainer assembly with spring instead of the 7/16 nut referred to in other posts. I used a long 1/2" ratchet extension to remove the plastic retainer assembly, removed the top half of the agitator and replaced the cogs, then replaced the agitator, plastic retainer assembly with spring, snapped the plastic cap back on, and replace the clothes softener cup.
Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....
After removing the pressed in cap inside the agitator i removed it from the machine with a socket wrench. Then it did not take long to figure out that the two peices snapped apart. then one look at the cogs (referred to as dog ears) i knew they where stripped and where the problem. Icanceled the service call and order the parts myself from this site. So it was very easy and i'm not sure how much money i saved but the bragging rights went along way with the wife, Thanks.
Removed the agitator assembly with a socket wrench and extension, replaced cogs, reinstalled assembly...took about 10 minutes because I dropped the assembly once, and had to reassemble it. An absolute "piece of cake."
Pulled up and removed the fabric softner dispenser. Then I pulled up and removed the cap barrier to have access to the screw. Removed the screw and pulled up the cloths mover. Tunrned the cloths mover over to remove the bearing cam to remove the broken agitator cogs and replaced them with the new ones. I held the bearing cam with my right hand and held the cloths mover with my left hand turning it slowly with my left hand and lightly pushing down with my right hand until the cloths mover made contact with the grooves of the shaft and it sunk down on the shaft. Replaced the screw and washer then the cap barrier , next the fabric softner dispenser. Took 10 min. to complete the job. Now my washer runs like new ! Plus, I have a happy wife!
Snap off softener dispenser. Pop off top of agitator with flat head screw driver. Use long handled socket ro remove agitator fastener. Lift off entire agitator assembly. Flip upside down on floor. Secure top section of agitator between feet and carefully unsnap but lifting upper portion. Look at placement of existing agitator cogs in upper section between feet. Remove cog retainer. Note position of cogs. Replace one cog at a time making sure they are repositioned the same way. Attach cog retainer. Place bottom portion of agitator in alignment and snap. Flip over and reinstall on washer center assembly. Place bolt and washer back into assembly and retighten. reattach cover and softener dispenser (if you have one). Done! Less than 15 minutes.
I followed the diagram and instructions included in the kit. I removed the plastic cover on the agitator, then another plastic cap inside the agitator. loosened a 7/16 bolt-removed agitator from washer. After removing agitator, Directional cogs and gear assembly inside agitator removes easily-pull out or turn upside down. Re-assembly was easy-almost fool proof . Using the instructions and diagram included with Directional cog package made it a snap.
popped off the softener dispenser, pulled out seal over nut assembly, used socket wrench with extention to loosen and remove nut holding cog assembly.slid holding ring off of the bottom (mine was black in color) pulled out old dog agitators put in new ones, reverse assembled the unit tightened it down, (be sure not to go too tight there is a rubber bushing under the nut) ran a small test load of laundry and it now works great!!!!
I popped the liquid detergent cap off of the top of the Agitator. I then removed the seal cap to expose the Agitator dog assembly and bolt. I removed the entire Agitator dog assembly and Agitator by removing the single 7/16? bolt. I pulled the old dogs out, put the new dogs in and reassembled the Agitator Assembly.Works like new!!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.