382960-1-M-Whirlpool-6800-Charcoal-Air-Filters.jpg
382960-1-S-Whirlpool-6800-Charcoal-Air-Filters.jpg 382960-2-S-Whirlpool-6800-Charcoal-Air-Filters.jpg 382960-3-S-Whirlpool-6800-Charcoal-Air-Filters.jpg

Charcoal Air Filters

PartSelect Number PS382960

This is a package of 2 filters.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $12.18
  • You Save

    $2.03
  • Your Price

    $10.15
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Grease Filter

Part Number 1847969

Sold individually.

$13.46
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 11 reviews What's this?
1-11 of 11
 

915 of 919 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJoseph from Las Vegas NV

Dirty grease filter

Slide grease filter about 1/2 inch to right (or left) using the D-ring attached to one side and then pull down and out. Push charcoal filter frame slightly to rear and pry down from front. Install new charcoal and grease filters by reversing process. No tools - 5-minutes max!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

362 of 365 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerDonna from Santa Paula CA

Vent grille was broken and exterior door panel was completely cracked and part of it had fallen off.

I actually followed one of your previous buyers who had the same issue as I. Replacing the grille vent is easy. The door was just a little harder as I wanted to make sure I did not break the glass. Unscrewed and popped off the old pane and snapped the new one in place and put the screws back in. On a side note your site was very easy to use and easy to find the parts I needed quickly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

203 of 341 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerCheryl from Elgin IL

Not too bad

Our Microwave Vent Grill was broken - and since I was ordering online, I figured I'd get the two filters as well. The Vent Grill was fairly easy to install. It was a little tricky getting it to fit in, but once in, it was just a matter of screwing in at the top.

The Filters were another matter. The FILTR-GRSE came out very easy, but what I didn't realize was when I ordered it, it only came in packs of 1. The Charcoal Air Filter came in packs of 2, so I assumed both did. Why, when you need two of each of these, do they sell one in single packages - and the other in packs of two? The Charcoal Air Filters were only replaceable by unscrewing the bottom of the microwave. The FILTR-GRSE were easy enough to just pop out.

Overall, not that bad of an install.

Help other customers find the most helpful instructions.

Were these instructions helpful?

206 of 409 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerFrederick from Three Rivers MI

Replace charcoal filters and grease screens and clean top exit ports

Removed old grease screens by sliding sideways and then pulling out of the grooves. (helps to have rubber gloves as the grease is slippery). Put pressure on the back of the charcoal filter rim and allow side closest to you to drop down slightly so you can get a fine flatblade screwdriver under and pop the filter out of the holder. Works same on both sides. Install new charcoal filters after cleaning the holder edges with soap and water and drying. Make sure charcoal filter is in the second set of holder grooves and snap in place. Replace new grease filters with the pull tabs down and facing the center. Slide the grease filter into the holder grooves a little further back than normal and (using the pull tabs) pull the filter back the other way until flush with the opening and in place. The top exit ports are removed by taking out 4 screws;however, two of them are attached to spring clips on the underside and it is easy to break off the tiny plastic ridges underneath. The other screws come out easily and the entire exit port piece can be removed and cleaned. To reinstall just snap exit port back in place and replace screws. If you have broken off the slender plastic ridges you can sometimes turn the screww a partial turn and engage what is left; if not you may have to put some rubber grommets or pieces to support the bottom and keep pressure on the exit port piece which is not locked by only two screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?

104 of 185 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerChris from Cedar Hill TX

Burned out light under microwave and filters needed changing

I just removed the multiple screws which held the hood cover on. I then attempted to remove the light bulbs from the socket. This proved impossible because the bulbs were so fragile from the heat and grease build up. To make this task much easier and probably safer, just replace the bulb housing and light bulb. The bulb housing unplugs very easily. Just replace it then screw your new bulb in. P.S. Be sure to unplug appliance before you start.

The filters are very easy to replace. No tools needed.

Hope this helps.

Help other customers find the most helpful instructions.

Were these instructions helpful?

62 of 63 people found this instruction helpful

Parts Used

  • Charcoal Air Filters

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerMartin from West Chester PA

The charcoal filters needed to be replaced

I dropped the grease filters ( two under the unit) and then removed the dirty charcoal filters. The new charcoal filters were then snapped into place and the washed grease filters were then put back. The entire job took about. 5 minutes. No tools needed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

63 of 125 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerPete from Saint Joseph IL

Grill on microwave was not staying in place

Took off old grill and replaced with the new grill. This is very easy. I am pleased with the service from your company. Parts arrived very quickly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

63 of 126 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerSusan from Hercules CA

Dirty filters

It was a simple replacement of grease filter and charcoal filter in microwave/hood combination. I did use a screw driver to pry out the filters, but otherwise no tools. It was easy and straightforward.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerAlma from Florence SC

Smoke alarm went off while frying

both of the pieces have a tab that help remove the pieces. They slip right out and new ones are putin place.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

CustomerChris from Boulder CO

Thought filters should be changed after 5 years of use.

Used hands to slide filters sideways, till they could be pried out with screwdriver or bare hands. When new parts arrived, easily slide new filters into position. In hindsight, we did not need to replace grease filter. I was able to clean one of those with ordinary dish soap, warm water, and a brush.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerKarolette from Virginia Beach VA

Microwave gill fasteners broke and would not stay in place.

Replaced grill and greese and charcoal filters.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-11 of 11