Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS382824
This middle spray arm kit includes an upper spray arm, a holder or hanger, water supply tube or delivery tube, split ring seal, and a screw. The function of these parts is to allow water to spray to all levels of the dishwasher so the dishes will come out completely clean. This kit has recently been redesigned. It does not include the upper support or mount, so consider ordering those parts as well if necessary. The spray arm is approximately 18 inches long, and all parts are white in colour. The only tool you will need to complete this repair is a Phillips screw driver.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
**Please note: This is a redesigned part. The top mounting clip and screw are no longer needed.
i ordered replacement part (you need the whole kit, not just the tube-the replacement "tube" wont fit in the old arm) got it in about 2 days, put it on in 5 mins. And i'm not usually good at this.Great and timely service.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I took a picture of the old set up to serve and my "directions" I removed one screw , put the new part on and re installed the screw. It was very, very easy and the quality of the parts you provided was excellent !
The repair was so easy!! I removed the spray arm by removing the screw and replaced the it with all the parts enclosed in the package. The repair took less than 15 minutes and was very easy.
a mater of unscrewing the part attached to the upper drawer...........placing new pieces together and srewing them on...............schematic on your web site was perfect.......had pieces sent over night.........wonderful experience
1. Saw problem - dishes not very clean and hose hanging down.2. Removed upper tray (hardest part until I found the trick of using needle nose pliers to hold locking tab on clip back while pulling up on clip).3. Realized problem when I saw large split in hose, so found model number and used PartSelect.Ordered replacement kit - evidently hose itself not available.4. about 3 days later - use FedEx ground unless you REALLY need it next day - parts kit arrived.5. Removed old parts (nut driver required) and installed new parts - keep track of sequence to remove old parts and where they go as there was no installation guide with kit. But it's not rocket science.Dishwasher now ready for another 10+ years.
Step 1. removed the single screw attaching the arm to the upper trayStep 2. removed the bad hose and support holder.Step 3. Attached the new holder on the upper tray, clips on.Step 4. inserted the new hose assembly in the hanger and washer bar on the enb of the arm.Step 5. tighten the screw - Done, 5 minutes!
Removed upper spray arm assembly using simple nutdriver hand tool and reinstalled new parts supplied as part of the complete repair kit.Broken door spring required screw driver to loosen bottom cover plate screws on front of dishwasher. Two screws were also removed that held the dishwasher under cabinet. to upper counter top. Dishwasher was moved out about 6 inches to gain access to sides. After screws were removed, on thet bottom front of the dishwasher, cover plate could be removed to gain access to side areas to remove broken door spring and replace with new parts. Reassembled in reverse order and the job is complete. Total repair time was approximately 30 minutes.
I removed the upper basket, tnen removed the spray arm with screwdriver. Screwed new spray arm to basket. Reattached basket to dishwasher and it works better than new. Thanks for the super service on the parts. I figure I saved over $100.00 on Sears service repairman to do this job. Thanks again. Jerry
I removed the screw from the old spray arem, snapped the new sleeve into place, replaced the screw and it was finished. The best part of the repair was the lightening fast delivery of the parts! Great service!
Went to parts select online, put in my washer info, the parts pulled right up complete with illustrated parts and it was very easy to order. The parts were actually at my door the next day, that was amazing. I think this is a very good source to get appliance parts.
1. Found this site in the Internet. (5 min.)2. Located the model number on my dishwasher. (1 min.)3. Determined my part on this site. (2 min.)4. Ordered my part. (1 min.)5. Waited for my part to arrive. (2 days)6. Opened the box. (1.5 min.)7. Removed one screw holding the old part in place. (0.5 min.)8. Reversed the process to installed new part. (0.5 min.)I live in a remote area. I'm used to waiting weeks to get repair services. Less than 15 minutes ordering and installing, no service fees and received my part in no time at all... I'm happy. Great site, great service.
Put the arm in place, secured with one nut, then underneath with a screw. I attached the little loop that holds the funnel part on and was done. The dishes in the upper rack have never been cleaner. This web site is the easiest web site I've ever navigated.
Once I recieved the parts, it was an easy process to remove the existing spray arm and reassemble the new arm in its place. The original hose and arm assembly had been inproved since the dishwasher was made and the replacement was an improved design. we also replaced the lower access panel that was damaged at the same time.
It was a quick repair. One screw and easy install on other parts.
After watching the excellent video on the PartSelect web site, the total repair using the Middle Spray Arm Kit and the Upper Spray Arm Mount took approximately 10 minutes to complete the repair. Also the delivery from PartSelect was fast (2 days).
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.