Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS382824
This kit has been redesigned. The supply tube is now one piece. This spray arm kit comes with an upper spray arm, holder, water supply tube and a screw. This kit does NOT include the upper support or mount.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
**Please note: This is a redesigned part. The top mounting clip and screw are no longer needed.
I first had to take the upper drawer of the dishwasher out so that I could get to the faulty part. This was a little tricky as there were two clips that had to be removed from the arm slides before the upper drawer could be removed. I then realized that the faulty part DID NOT exactly match the repair part I received. The original connection wand was in two pieces where the repair part was all one piece. That required a bit of thought before I began the repair. There was NO drawing accompanying the new part, so I had to decide how the part would be connected. After a little trial and error, I determined the arrangement of the repair part and completed the repair. All in all, it went well, but there was a few anxious moments when I first saw the difference between the original part and the new part.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I screwed the rack mount to the spindle usingthe extra screw I ordered. I removed the upper dishrack's front stops and slid the rackout. I clamped the mount to the dishrack. I screwed the rotor to the spindle with the screw that came with the rotor kit. I slipped the feed tube mount over the end of the tube and clamped it on the dishrack. I replaced the rack in the slides and replaced the front stops.I had a hard time driving the screws. The slots are crossed but do not seem to be standard Phillips. The screws were hard to drive into the holes in the hard plastic. Before I could drive the mount screw all the way, the slot was too stripped to use.
Removed upper basket and installed the arm. New snap in didn't require phillips screwdriver as old one and new support had split to insert. Replacing upper spray spinner dropped screw down around pump. This caused misery unassembling lower covers to receive Stainless Steel, so magnet won't help ended up with mirror and hemistat to reach through large screen figures. So make sure to put towel or something in the bottom to catch parts.
Used nut driver to remove old spray arm assembly on top rack. Reinstalled the new assembly, clamped the holding assembly onto the rack, tightened the holding assembly--that's it.
First I removed the upper basket from the dishwasher by taking off the end clips from the right and left hand slides. The clips are removed by prying them gently upward with a screwdriver.Second I removed the old spray arm assembly by slipping the old tube off of the rotary fitting.Third I removed the center screw from the rotary fitting which holds the upper spary arm in place. I also removed the small plastic piece (block) which is clipped to the wire basket.Fourth I installed the new spray arm assembly making sure to orient the plastic spacer block so that the spray arm rotates freely. The spacer block clips on the wire tray and the assembly is held in place with a single screw.The new assembly includes a one piece extension tube and end funnel so it is really easy to install.
I removed the screw that held the arm in place. Make sure you remember where it is supposed to go & keep the little clip that holds it to the top rack. Put the new parts in just the way the old ones came out. Don't forget to use the new screw & washer, my old one was a little stripped. Easy, just as the other posts said (and reading them gave me the confidence to try this myself!)
First I removed the old spray arm and water supply tube. There was one screw at the top of the spray arm and the tube holder clip. The new water supply tube is one piece, not three like the old one (which is why it melted) so the tube holder clip is severed so it can be placed around the tube. The old clip is a solid piece so if you only get a new tube you won't be able to get the old clip around it. I didn't need a new spray arm but thought it would be a good idea to replace the entire spray arm apparatus. I took note of how the old spray arm was placed and put the new one right in! It was very easy.
all i did is to remove the screws out take out the damaged ones and replace them the new ones put the screws back, it was very easy, it save me time and money. Thank-you part select.com
Removed old parts, removed one screw. Then installed new kit, replaced one screw.No problems.
Received unit in two or three days even during Christmas rush.Replaced sprayer with just a screwdriver in no time and dishwasher is working perfectly. PartSelect is the only way to go. I have used them for other parts and they are always prompt and easy to identify parts on their website.
i ordered replacement part (you need the whole kit, not just the tube-the replacement "tube" wont fit in the old arm) got it in about 2 days, put it on in 5 mins. And i'm not usually good at this.Great and timely service.
I took a picture of the old set up to serve and my "directions" I removed one screw , put the new part on and re installed the screw. It was very, very easy and the quality of the parts you provided was excellent !
The repair was so easy!! I removed the spray arm by removing the screw and replaced the it with all the parts enclosed in the package. The repair took less than 15 minutes and was very easy.
a mater of unscrewing the part attached to the upper drawer...........placing new pieces together and srewing them on...............schematic on your web site was perfect.......had pieces sent over night.........wonderful experience
1. Saw problem - dishes not very clean and hose hanging down.2. Removed upper tray (hardest part until I found the trick of using needle nose pliers to hold locking tab on clip back while pulling up on clip).3. Realized problem when I saw large split in hose, so found model number and used PartSelect.Ordered replacement kit - evidently hose itself not available.4. about 3 days later - use FedEx ground unless you REALLY need it next day - parts kit arrived.5. Removed old parts (nut driver required) and installed new parts - keep track of sequence to remove old parts and where they go as there was no installation guide with kit. But it's not rocket science.Dishwasher now ready for another 10+ years.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.