Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS382824
This kit has been redesigned. The supply tube is now one piece. This spray arm kit comes with an upper spray arm, holder, water supply tube and a screw. This kit does NOT include the upper support or mount.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
**Please note: This is a redesigned part. The top mounting clip and screw are no longer needed.
I noticed the upper bushing washer was worn thin. this caused the lower spray arm to rise too high and wobble during all the wash cycles. Also the rotation of the lower spray arm was wearing grooves in the lower bushing. I removed the retaining nut and simply replaced teh defective parts. While I was at it I figured equal wear might be evident on the upper spray arm so I bought a complete rebuild kit to bring all rotational parts back to new and equal preformance that was achieved by removing the ss screw and removing the upper spray arm, bushing and clip then replacing them in the order of removal. Noticed a huge difference in the quality of the washed dishes!! Thanks Parts Select 100% to yoru company!!
Help other customers find the most helpful instructions.
Were these instructions helpful?
The part came so fast without extra shipping. It took only 10 minutes to replace water tube and upper spray arm. I only had to remove one screw. Replaced with new parts and reinstalled screw. It was easier and cheaper than calling a repairman.
As others have described, this replacement was very easy. The new spray arm is solid plastic instead of rubber (which had deteriorated and was the part that needed replacing). So it should last longer.You have to keep and reuse the mounting bracket that attaches the spray arm to the upper rack, so don't throw that away!The replacement was super-easy, and as others have commented, the dishes haven't been this clean for a long time. Well worth it.
The mounting bracket was broken.The parts ordered were a direct match due to the fantastic pictures supplied on this site.A dealer wanted to order it and then I would have had to drive and pick it up - no way.partselect.com first time user - very easy.
This gets a little lengthy... but it explains where Cascade Dishwashing Powder came up with its brand name - it's been a cascade project.I started by replacing the Middle Wash Arm Tube as the old tube developed leaks. As others have stated this is a new design but directly replaceable and easy to do.This didn't solve the cleaning issue so reading the experiences of others on this site realized I also had broken parts in the Upper Spray Arm Assembly and the Upper Wash assembly. I replaced these and the dishes were suddenly much, much cleaner. These were very easily replaced.I did find that I did not need the Mount for the upper spray arm (PS402277) as a redesign of the Upper Spray Arm Mounting bracket no longer required it - the bracket simply clipped in -the diagram was out of date. Everything seemed to go well for about 3 loads when the dishwasher started leaking heavily out of the bottom of the door. I then noticed that the lower Wash Arm Bearing Ring and the Seal, Lower Spray Arm had disintegrated so I replaced those but this didn't affect the leaking. Someone had stated that if the lower wash arm assembly had too much 'wobble' that it cause 'waves' that would leak out the front door... mine had some wobble so I added a nylon washer from Ace Hardware that reduced wobble but still leaked.I then replaced the Door Seal Kit - this was by far the most difficult part as the door needed to be removed and it was somewhat difficult - and it seemed apparent after we had removed the door that these parts weren't the problem but we replaced them anyway. Also, someone else had noted that they had to attach the door seal (this is NOT the gasket that goes around the door opening) with a sealant - I had the same problem; the original seal fit tightly with friction but the new replacement required an adhesive - I used silicone. Still leaked.From here on I can't guaratee any useful information: I took the strainer screen out of the bottom of the dishwasher and found one slightly loose screw holding what I believe is the 'pump outlet' according to the diagram. I had also read that the water fill is controlled not by the float at the bottom of the washer but by the electronics and it was suggested that I disconnect the DW from the power to 'reset' the timer, this I did and hit the 'Cancel' cycle a couple of times to make sure that all programs were cancelled. Whether any of this made a difference I have no idea - except that the dishwasher suddenly stopped leaking and hasn't leaked a drop for at least 20 washes. So I don't know, for sure, why it leaked or how I fixed it, but it's working and washing great now - except the tines on the lower rack are beginning to rust out and breaking off. The rack is pretty expensive but so far I've saved a lot of money and my family thinks I'm a dishwasher genius.
The video offered was perfect and walked me through the exact process and gave me the confidence i could handle this repair myself. It was very intuitive and went step by step. Thank you for taking the time to post the repair steps on video. Ordering the parts was very simple and they arrived on time. Flawless in every aspect. i would recommend your company.
First of all, we were very impressed with the ease of finding the parts, the ordering, and the velocity in which the parts were shipped. We received them the next day. I had to remove one of the screws from the old kit, since the new one only came with one. I looked at the diagram on the website of the assembly, and also remembered what the assembly looked like before I took it apart. The first time I tried it, I could not get the spray arm to spin without hitting the dishwasher rack. Since I had ran out of time, I had to wait until the next day. Once I started, I realized that I had the mounting bracket on backwards. Once I turned it around, I tightened the screws, and it was done within 5 minutes.
Bottom wash arm bearing and seal were severely worn and leaking. Replaced in about one minute with new parts from PartSelect.com, and took the opportunity to clean out the arm -- stringy, fibrous matter was clogging two jets.Top arm horizontal rubber supply tube was disintegrating and leaked. Replace with Spray Arm Kit -- this took maybe two minutes! Lastly, two to of the upper right-rear folding rack tine clips were broken -- replacement was difficult as the old, broken clips were very stiff and came off only after much physical persuasion! New clips were installed easitly -- in a "snap". Time ~ 5 minutes.Best of all, the new parts were delivered to my home within 36 hours of my internet order. I thought the prices were fair, too. Thanks.
Removed one screw to get the spray arm off the rack, one other screw to disassembly the spray arm assembly. Replaced worn and damaged parts. Installation was reverse order of disassembly.
we removed the cracked pieces and attached the new spray arm. it took some time because the new arm looked different than the old,but we did it.... I was the one to order the parts needed i had never done this before my husband said it was broken and we needed to buy a new dishwasher ( he was less than thrilled about that) so i decided to do this myself and find the parts. my husband was very surprised that i did it.... AND SO WAS I... IF I CAN DO IT YOU CAN DO IT!
Removed old phillips head screws /w washers from spray arm kit and mounting bracket. (You'll need to keep one screw/washer set.) Attached new mounting bracket and screwed securely. Attached spray arm with new screw/washer and I was good to go. Piece of cake!
Hey parts select, I'm Julia's husband and the repair was a simple remove and replace. Only one screw to hold the manifold together and the mounting hardware that we had to order separately was a snap in piece which was different form the original but went in just fine. You saved me from having to buy a new dishwasher which Julia was more than happy to go shopping for!! Thanks!!
replaced spray arm, but this did not resolve the problem. The troubleshooting guid (inside kick panel) indicated the check valve may be stuck. We had quite a bit of lime build up, so I suspected the loose deposits may be stuck. I removed all of the deposits, disassembled the lower unit.Removed lower spray arm, removed spry tube. The tube is two pieces. first the upper portion must be removed (two screws-place towel on base of tub to preven screws from falling into the chopper area), and then the lower portion simply rotates clockwise 1/8 of a turn. The attachment for lower spray arm has a small plastic bearing, careful not to drop it.The dishwaser then had to be pulled out and turned on the side. I removed the entire lower unit by removing the white tabs (3). Careful, because the unit is now free to drop into the tub. Next I removed the pump. This is tricky as you have to remove the aluminimum bracket to get to the mountin bolt. The bolt turns out easily w/socket and extension. The pump motor is then rotated counter clockwise, and pulled from the pump. Takes a little force as the gasket makes for a tight fit. I then removed the choper / pump unit from the basin. The build up behind the chopper screen was extensive, so I had to remove the screen and then the chopper cover. After cleaning, the check valve was unplugged and I reassembled the unit.Dishwasher works great now.
We were told by a repair guy to buy a new dishwasher-about a $900+ cost to replace. Then a local parts place and Sears each quoted us $85 for the part plus $129 to come out. Found your website and bought the part for $17. Also bought a hard rubber gasket that fits on the bottom of the door for $8. The brackets that came with that last part were the hardest to install, but the gaskets took 15 minutes. We did glue another strip of the long door gasket along the area under the door lip. Works great! Saved over $800. You rock!
I removed the screws on the door cover and snapped in the new clipfor the arm I just removed one screw and replaced the arm
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.