Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS382824
This kit has been redesigned. The supply tube is now one piece. This spray arm kit comes with an upper spray arm, holder, water supply tube and a screw. This kit does NOT include the upper support or mount.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
**Please note: This is a redesigned part. The top mounting clip and screw are no longer needed.
1. Saw problem - dishes not very clean and hose hanging down.2. Removed upper tray (hardest part until I found the trick of using needle nose pliers to hold locking tab on clip back while pulling up on clip).3. Realized problem when I saw large split in hose, so found model number and used PartSelect.Ordered replacement kit - evidently hose itself not available.4. about 3 days later - use FedEx ground unless you REALLY need it next day - parts kit arrived.5. Removed old parts (nut driver required) and installed new parts - keep track of sequence to remove old parts and where they go as there was no installation guide with kit. But it's not rocket science.Dishwasher now ready for another 10+ years.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Step 1. removed the single screw attaching the arm to the upper trayStep 2. removed the bad hose and support holder.Step 3. Attached the new holder on the upper tray, clips on.Step 4. inserted the new hose assembly in the hanger and washer bar on the enb of the arm.Step 5. tighten the screw - Done, 5 minutes!
Removed upper spray arm assembly using simple nutdriver hand tool and reinstalled new parts supplied as part of the complete repair kit.Broken door spring required screw driver to loosen bottom cover plate screws on front of dishwasher. Two screws were also removed that held the dishwasher under cabinet. to upper counter top. Dishwasher was moved out about 6 inches to gain access to sides. After screws were removed, on thet bottom front of the dishwasher, cover plate could be removed to gain access to side areas to remove broken door spring and replace with new parts. Reassembled in reverse order and the job is complete. Total repair time was approximately 30 minutes.
I removed the upper basket, tnen removed the spray arm with screwdriver. Screwed new spray arm to basket. Reattached basket to dishwasher and it works better than new. Thanks for the super service on the parts. I figure I saved over $100.00 on Sears service repairman to do this job. Thanks again. Jerry
I removed the screw from the old spray arem, snapped the new sleeve into place, replaced the screw and it was finished. The best part of the repair was the lightening fast delivery of the parts! Great service!
Went to parts select online, put in my washer info, the parts pulled right up complete with illustrated parts and it was very easy to order. The parts were actually at my door the next day, that was amazing. I think this is a very good source to get appliance parts.
1. Found this site in the Internet. (5 min.)2. Located the model number on my dishwasher. (1 min.)3. Determined my part on this site. (2 min.)4. Ordered my part. (1 min.)5. Waited for my part to arrive. (2 days)6. Opened the box. (1.5 min.)7. Removed one screw holding the old part in place. (0.5 min.)8. Reversed the process to installed new part. (0.5 min.)I live in a remote area. I'm used to waiting weeks to get repair services. Less than 15 minutes ordering and installing, no service fees and received my part in no time at all... I'm happy. Great site, great service.
Put the arm in place, secured with one nut, then underneath with a screw. I attached the little loop that holds the funnel part on and was done. The dishes in the upper rack have never been cleaner. This web site is the easiest web site I've ever navigated.
Once I recieved the parts, it was an easy process to remove the existing spray arm and reassemble the new arm in its place. The original hose and arm assembly had been inproved since the dishwasher was made and the replacement was an improved design. we also replaced the lower access panel that was damaged at the same time.
It was a quick repair. One screw and easy install on other parts.
After watching the excellent video on the PartSelect web site, the total repair using the Middle Spray Arm Kit and the Upper Spray Arm Mount took approximately 10 minutes to complete the repair. Also the delivery from PartSelect was fast (2 days).
Researched problem and found your site, very informative and helpfull. Bought the parts from you, very good price and speady delivery. One problem, I didnt look at the job BEFORE I purchased parts... When I took the top rack out to install the nice new parts kit I discovered the only problem was the connecting hose had come disconnected! I reconnected hose and all is well... Moral of this story, look before you purchase anything for the repair!!! I will be keeping the parts for when I may really need them. LOL
most everything snapped easly into place only one screw to deal with. very easy repair.
Removed the upper spray arm and hose to rear of washer by detaching the hose clip at the back of the upper dish basket and removing the screw at the bottom of the spray arm. Reinstalled the new one piece hose assembly and the new upper spray arm by replacing the screw at the bottom of the spray arm and attaching the new hose clip at the back of the upper dish basket.My original top spray unit was held in place by two screws. The new top spray unit uses only one screw but the second attachment point is still part of the new unit. I drilled a hole for the second screw. I removed the two screws that held my damaged top spray in place and removed the damaged top sprayer. The small hose to the top sprayer easily slides out of the unit when the screws are removed. I reinstalled the new top sprayer using the two original screws.
First of all it was Easter Dinner and the mount borke. Ughhh... I driled some holes and inserted wire to give it the McGiver effect to get me by. Even the mother in law was impressed! Once new parts arrived I only needed a screwdriver. Be carfeul when screwing in the new screw to hold the new sparyer to the new mount. GO SLOW..Let the plastic "give" as you tighten the screw. To fast and you could twist the new monting shaft off. And just barely snug up the screw. Being to tight, the hot water may expand the plastic durring cylcles and cause undo stress.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.