| |
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
CustomerDavid from Oxford MD
The upper spray arm supply tube split
1. Saw problem - dishes not very clean and hose hanging down.
2. Removed upper tray (hardest part until I found the trick of using needle nose pliers to hold locking tab on clip back while pulling up on clip).
3. Realized problem when I saw large split in hose, so found model number and used PartSelect.
Ordered replacement kit - evidently hose itself not available.
4. about 3 days later - use FedEx ground unless you REALLY need it next day - parts kit arrived.
5. Removed old parts (nut driver required) and installed new parts - keep track of sequence to remove old parts and where they go as there was no installation guide with kit. But it's not rocket science.
Dishwasher now ready for another 10+ years.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerGreg from Freeburg IL
Washer arm hose developed a hole
Step 1. removed the single screw attaching the arm to the upper tray
Step 2. removed the bad hose and support holder.
Step 3. Attached the new holder on the upper tray, clips on.
Step 4. inserted the new hose assembly in the hanger and washer bar on the enb of the arm.
Step 5. tighten the screw - Done, 5 minutes!
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerDean from Mosinee WI
Broken door spring & upper spray arm assembly.
Removed upper spray arm assembly using simple nutdriver hand tool and reinstalled new parts supplied as part of the complete repair kit.
Broken door spring required screw driver to loosen bottom cover plate screws on front of dishwasher. Two screws were also removed that held the dishwasher under cabinet. to upper counter top. Dishwasher was moved out about 6 inches to gain access to sides. After screws were removed, on thet bottom front of the dishwasher, cover plate could be removed to gain access to side areas to remove broken door spring and replace with new parts. Reassembled in reverse order and the job is complete. Total repair time was approximately 30 minutes.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerGerald R. from Williston VT
Rotted spray arm in dishwasher.
I removed the upper basket, tnen removed the spray arm with screwdriver. Screwed new spray arm to basket. Reattached basket to dishwasher and it works better than new. Thanks for the super service on the parts. I figure I saved over $100.00 on Sears service repairman to do this job. Thanks again. Jerry
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers, Socket set
CustomerSandra from Birmingham AL
Spray arm rotted over time
I removed the screw from the old spray arem, snapped the new sleeve into place, replaced the screw and it was finished. The best part of the repair was the lightening fast delivery of the parts! Great service!
|
3 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRoger from Sandwich IL
Hose on original equipment dry rotted.
1. Found this site in the Internet. (5 min.)
2. Located the model number on my dishwasher. (1 min.)
3. Determined my part on this site. (2 min.)
4. Ordered my part. (1 min.)
5. Waited for my part to arrive. (2 days)
6. Opened the box. (1.5 min.)
7. Removed one screw holding the old part in place. (0.5 min.)
8. Reversed the process to installed new part. (0.5 min.)
I live in a remote area. I'm used to waiting weeks to get repair services. Less than 15 minutes ordering and installing, no service fees and received my part in no time at all... I'm happy. Great site, great service.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerTodd from Dublin CA
Spray arm was loose and the mounting bracket was broken
Put the arm in place, secured with one nut, then underneath with a screw. I attached the little loop that holds the funnel part on and was done. The dishes in the upper rack have never been cleaner.
This web site is the easiest web site I've ever navigated.
|
1 of 2 people found this instruction helpful
Parts Used
-
- PANEL
- Middle Spray Arm Kit
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerKevin from San Jose CA
Spray arm connection not functional
Once I recieved the parts, it was an easy process to remove the existing spray arm and reassemble the new arm in its place. The original hose and arm assembly had been inproved since the dishwasher was made and the replacement was an improved design. we also replaced the lower access panel that was damaged at the same time.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJohn from North Stonington CT
Water coming out door
Researched problem and found your site, very informative and helpfull. Bought the parts from you, very good price and speady delivery. One problem, I didnt look at the job BEFORE I purchased parts... When I took the top rack out to install the nice new parts kit I discovered the only problem was the connecting hose had come disconnected! I reconnected hose and all is well... Moral of this story, look before you purchase anything for the repair!!! I will be keeping the parts for when I may really need them. LOL
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
Customerfred from york PA
Dishes not clean, water leaking from front of dishwasher
most everything snapped easly into place only one screw to deal with. very easy repair.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerDeborah from New Paltz NY
Water was not dispersing properly which left dishes less than clean
I removed the end clips so I could slide out the upper rack........I recommend doing this carefully inorder to reuse the clips. All the repairs were easy..........at first I thought the lower arm was not tightened enough, but a simple search told me that it is supposed to "wobble".
Thank you for making it so easy to find the right parts. You do an excellent job of organizing parts by model #.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerITS from Carlstadt NJ
Water can't go to upper rack.
first I removed the Bracket screw underneath of the upper rack , after that I removed the Bracket with my hand by bushing it downward (it removed complete assembly "Bracket & Spray Arm kit") the I removed the other screw to remove the Bracket completely, then I installed the new part's by reversing all above steps, finally I installed the Two screws back again.
It is so easy!!!!!!!!!!!!!!!!!!!!!
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerMichael from Provincetown MA
Leaky door and broken spray arm
Removed the old door gasket and gently pushed the new one in place in less than 5 mins .The new one fit perfectly, and.......No leaks !
The cracked upper spray arm assebly also was disassembled in 5 mins, and quickly replaced without any problems...All parts fit and worked great.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDennis from Yorktown VA
Spray arm mount broken and supply tube cracked
First, I compared the parts visually. The mount is a slightly different design. I removed the old mount/spray arm and tube by removing the single screw through the upper mount and un-clipping the rear tube mount. Next I assembled the new parts using the old spray arm as a guide. Note: Installing the new screw for the spray arm into the new mount proved very difficult and I needed to enlarge the pilot hole slightly in order to assemble. I proceeded to attach the new mount to the upper rack and installing the rear tube mount. The new design of the mount eliminated the need for the upper mount and even if I wanted to install it, it will not fit the new design. Overall, an easy repair with a couple of hiccups.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Socket set
CustomerElizabeth from New Oxford PA
Holes in spray arm
Was having trouble for a couple of years that my top rack wasn't getting clean. Didn't check it out until my son bought a new dishwasher and hubby installed it. Couldn't believe the holes in the spray arm, went online googled it, found the part and in 2 days the part was at our door. Was very easy to install and now my dishes are very clean again!
|