382122-1-S-Whirlpool-660579            -Broil Element - 208V
382122-1-S-Whirlpool-660579            -Broil Element - 208V 382122-2-S-Whirlpool-660579            -Broil Element - 208V http://www.partselect.com/Schematics/Whirlpool/Whirlpool_Thumb/QRACIBEO.gif

Broil Element - 208V

PartSelect Number PS382122

This broil element is found on the roof of the oven and has push-on terminals.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Little to no heat when broiling.
  • Element will not heat.
  • Little to no heat when baking.
  • Compare At

    $50.15
  • You Save

    $8.36
  • Your Price

    $41.79
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 11 reviews What's this?
1-5 of 11
 

29 of 32 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRobert from Baton Rouge, LA

Bake element burned out

Replacement was relatively easy. Oven door was pulled off hinges after removing 2 mounting screws nearest the hinges. After shutting off power at the breaker, screws (2 each) holding elements were removed. Elements were pulled into oven ~ 4 inches exposing wiring and clips. The clips pulled free with just a little wiggling by hand and were easily pushed back on by hand. Then reverse to finish.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 10 people found this instruction helpful

Parts Used

  • Broil Element - 208V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerStarla from Vashon, WA

Burnt out broiler element

Turned off power to range because I was scared. Unscrewed broiler element, pulled part forward and pulled off wires that were attached to the back, attached wires to new element, pushed it back in place, screwed it back on to oven. Cooked my bruchette!

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerLee from Austin, TX

Both heating elements would not work.

After shutting off the power, I removed the door and oven racks. Then, by using a screwdriver, I removed each element one at a time and replaced with the new element. Each element pulled away from the back wall and was connected electrically by Sta-Kon connectors. All went well, and the unit was operational in about 30 minutes. I still have to remove the oven from the wall to replaced the two door springs.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 11 people found this instruction helpful

Parts Used

  • Broil Element - 208V

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerDAVID from COTTAGE GROVE, WI

Broil element was burned out

1. Move oven out from wall 2. Remove back panel of oven, 8 screws 3. Remove 3 screws inside oven holding element 4. Pulled wire connections off of element 5. Reverse procedure to install new element

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Broil Element - 208V

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerRobert from Atlanta, GA

Broiler unit would not heat

The broiler unit had disintegrated at both connections. I removed the two screws in the top of the oven holder the unit, pulled out the unit, measured and ordered a replacement.

To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 11