382106-1-S-Whirlpool-660533            -Surface Burner - 8" - 2600W
382106-1-S-Whirlpool-660533            -Surface Burner - 8" - 2600W 382106-2-S-Whirlpool-660533            -Surface Burner - 8" - 2600W 382106-3-S-Whirlpool-660533            -Surface Burner - 8" - 2600W http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/7689.gif

Surface Burner - 8" - 2600W

PartSelect Number PS382106

NOTE: The manufacturer recommends that you replace the burner receptacle at the same time.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Element will not heat.
  • Compare At

    $23.83
  • You Save

    $3.97
  • Your Price

    $19.86
In Stock
Order within the next 4 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Burner Receptacle

Part Number 11728056

Order within the next 4 hrs and your part ships today!
$8.16
In Stock

Standard Y-Frame Surface Burner - 6" - 1500W

Part Number 382104

The manufacturer suggests replacing the receptacle at the same time.

Order within the next 4 hrs and your part ships today!
$19.54
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 31 reviews What's this?
1-5 of 31
 

51 of 59 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerJonathan from Lilburn, GA

8 inch burner wouldn't come on. Wires shorted out

One screw holds the block onto the stove top. Had to clean out fitting for phillips screwdriver or screw would have stripped because it was old with lots of buildup. Even cleaned out, this screw required great force with phillips screwdriver to keep from stripping. Caution! If you strip it, you'll have to drill it out! The rest was a snap. Cut the old wires leading to the old block (not too close to where wires disappear into back of stove, though!). Strip insulation off both wires and attach with the connectors that came in the kit. Then push the wires into the block, and finally, attach the block back to the stove top (new screw is supplied). Restore power and everything should be fine. One problem: Roper/Whirlpool built their appliance in such a way that when the connector block shorts out, it usually takes the infinite switch with it. So I ended up having to go back and purchase that switch as well (which just so happens to cost twice to three times as much!). If you put it all back together and it still doesn't work, that's probably what happened, so go ahead and remove the knob panel and check that switch (it's right behind the control knobs on the front). You will probably find a burned connector at the back top left or the switch. Don't forget to write down which wire goes where (or just take a picture of it).

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 15 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerMary from Lebanon, CT

1 had 2 large burners not working at all, and was cooking everything on the 2 smaller burners

It was so simple to repair - all I had to do was slide the older burners out and slide the new ones in - it took less than 10 min to complete the whole job! No tools used at all.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 15 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRolland from Walla Walla, WA

Receptacle burned out, due to short

This was the second repair of the same problem. I realized this time that there was a poor connection between the burner and the receptacle causing a arch, creating extra heat and burning out the receptacle.
All that I had to do was to cut two wires to the existing receptacle assembly and use the wire nuts to connect the new assembly and one philips screw holds it in place...The kit required me to assemble it first and there were four items to put together. No problem....

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 13 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerScott from Pleasant Valley, CT

Burner was arching or not heating up.

I followed the instructions on removing the existing burner, recepticle, and section of wire. Then followed same instructions for reinstalling above new parts. The instructions were simple and straight forward. The only gluich was that I had to drill out the rivets holding in the old hold down clips. I drilled these out with an 1/8" bit on the burner side off the opening.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerSteve from Mount Carmel, PA

Heating element and socket needed to be replaced

It was very easy, the element is held in place by a point that protrudes from the element's frame through a hole in the stove top. This hole is located directly across from the electrical socket your bheating element plugs into, under the stove top. Push the heating element in towards the socket and the heating element can now be lifted up and out of the burner tray. Remove the burner's reflector tray. Remove the single screw securing the elements electrical socket to the stove top. Lift the stove top up and secure. Remove socket and cut wires about 4 inces from the old socket. place shrink wrap over each wire and wire nut new socket to existing wires. place shrink wrap over wire nuts and heat to secure. reverse proceedure and test.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 31