374693-1-S-Whirlpool-4451665           -Oven Sensor
374693-1-S-Whirlpool-4451665           -Oven Sensor 374693-2-S-Whirlpool-4451665           -Oven Sensor

Oven Sensor

PartSelect Number PS374693

This part detects the temperature within the oven cavity.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Compare At

    $81.95
  • You Save

    $13.66
  • Your Price

    $68.29
In Stock
Order within the next 7 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.8 / 5.0, 2 reviews What's this?
1-2 of 2
 

31 of 40 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerChristy from Paso Robles CA

After using the "self-clean" option, the panel blew out and the door remained locked. We knew we burnt fuses but didn't know which ones. We had a technician come out and tell us which ones. ($70.00) he quoted us a price of $495.00 for parts and labor. We did the repair ourselves and cost us $157

The hardest part was getting the oven out. The double oven is pretty heavy.

The screws were on the sides under a removable strip. Have a table about the same height as the base of the oven. It was easy to slide it straight over to the table.

The schematics are on top of the oven. Although you probably won't need them for the parts we replaced. When you have the oven out and the back panel removed, it is easy to identify the exact parts you are replacing. The part numbers were the same on the fuses. The thermostat was a simple pull apart. Then undo the 2 screws inside the oven. The heat sensor required some figuring. There is a pin that holds it in place in a plastic casing. We used a small flat head screw driver to push the pin flat to loosen it from the casing. This part was behind the digital panel and the only one that didn't require the oven coming out.

We would easily do this project again and glad we did. We saved $340.00 by doing it ourselves. I am glad I found PartSelect.com

Make sure you turn off the breaker to the appliance first. You don't want any electrical surprises. The hospital bill would be more expensive than the repairman !!

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 14 people found this instruction helpful

Parts Used

  • Oven Sensor

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerAnthony from Charlottesville VA

Digital control panel went haywire.. control would not function

First I removed the two screws that hold the sensor element in place (from inside the oven). I then pulled the sensor out about three inches and disconnected the two wires, and connected the new sensor. Screwed the sensor back into the back oven wall..

There was some confusion with the repair tech who first thought I would have to pull the pven out and remove the sensor from the back so that increased the time for repair. After pulling the oven it was obvious that the repair could be made from the inside..
The repair Tech's diagnosis of the problem was correct a nd fast. Part cost $75 on line ($102 from dealer locally). Saved over $125 cost compared to local repair man's visti.and that is a low side guess. Repair tech was very communicative.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-2 of 2