Quick Question!

Have you ever purchased from PartSelect.com before?

373087-1-S-Whirlpool-4392065           -Maintenance Kit
373087-1-S-Whirlpool-4392065           -Maintenance Kit 373087-2-S-Whirlpool-4392065           -Maintenance Kit 373087-3-S-Whirlpool-4392065           -Maintenance Kit http://www.partselect.com/Schematics/Whirlpool/BJVPXWJX.gif

Maintenance Kit

PartSelect Number PS373087

This maintenance kit or dry repair kit is used for dryers. The kit includes the drum belt, drum support rollers, one idler pulley, four tri-rings, and one clip. If your dryer is making loud, squeaking, and squealing noises while the drum is turning, or the drum has stopped turning, using this maintenance kit is the solution. The tools needed for this installation project are: putty knife, Phillips screwdriver, 5/16 nut driver, and a small flat blade screw driver. This kit can be used for gas and electric dryers. Remember to unplug the dryer from the power source before beginning this project.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Noisy.
  • Will not tumble.
  • Will Not Start.
  • No heat or not enough heat.
  • Marks left on clothes.

Compare At

$53.17

You Save

$8.86

Your Price

$44.31
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Multi Rib Belt - 92-1/4"

Part Number 346995

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the motor rotates, the belt begins to move and turns the drum. If you notice the drum of your dryer is not spinning during the dry cycle, but you hear the motor running, your belt may have snapped and it will need to be replaced. This belt features four ribs and three grooves, however it replaces a wide variety of belts including wider styles that had five ribs and four grooves. When installing this part make sure the grooves are facing down, against the drum. This replacement part is 92 1/4 inches in length, and 1/4 inch wide. Before you begin any repair work, make sure your dryer has been unplugged.

$14.56
In Stock

Rear Drum Support Roller Kit

Part Number 347627

The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings and one palnut (or retaining washer). The kit does not include a belt or idler pulley and rollers are not sold individually. The drum support roller kit may need to be replaced if the dryer is noisy or will not tumble. The tools needed to complete this repair are a putty knife, Phillips screw driver, and a 5/16 nut driver. It is recommended to look at the rear felt before reassembling the dryer to ensure there are no gaps or damage. This is an OEM part sourced directly from the manufacturer.

$12.47
In Stock

Idler Pulley Assembly

Part Number 11743765

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum and attaches to the idler pulley wheel. If your dryer will not start or tumble, takes too long to dry, or is noisy during operation, you may need to replace the idler pulley assembly. Make sure to disconnect power before installing this part, and work gloves are recommended to protect your hands. While the dryer is disassembled for this repair, consider replacing the drive belt as well. You will need a putty knife, a Phillips screwdriver and a 5/16 nut driver for this repair.

$10.04
In Stock

Tri Ring

Part Number 11755850

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

$5.96
In Stock

Support Roller Clip

Part Number 11746832

Sold Individually.

$3.02
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 49 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Socket set
Customer: Larry from PHILADELPHIA, PA

Dryer was making loud noises.

Pretty much followed your great video: . Watching it gave me the confidence that I could accomplish the job myself.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Socket set
Customer: William from HUDSON, MI

Drum wouldn't move. Belt broken.

Opened the cabinet and removed the drum. Cleaned out the dryer fuzz. found that the roller stabilizer wasn't in place; apparently due to a previous repair. Replace both rollers and the roller stabilizer and prepared to replace the drum. But because I live alone, I didn't have anyone to hold the drum while I connected the belt to the motor. But, I did have three unused balloons which I partially inflated and set the drum on them in the bottom of the cabinet while I hooked up the belt to the motor. Put everything back together and it is now drying my clothes again. :)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Socket set
Customer: William from STANWOOD, WA

Squealling when dryer starts up then squeals off and on while running

We had to take the dryer apart first to figure out what the problem was. Put it back together after determining what was the problem, order parts ,receive parts in the mail, tear dryer back apart install new parts, close dryer up, test run, Get Thank-you kiss from wife!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Socket set
Customer: John from WEST ISLIP, NY

None

Followed the video your company has.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Kevin from QUINCY, MA

Belt snapped

Followed the directions, top held in place by plastic clips, used flat bladed screw driver to gently pry upwards until they released. Cleaned inside of dryer. Check for lint, just about none. Two screws retain the front panel. Disconnect the door switch. Installed new rollers, then installed the rear drum seal which can be messy and the hardest part of the whole job. I applied the adhesive to the lip and slipped the seal onto the lip, the adhesive was setting by the time I was done, but it's glued 360 degrees around the periphery. Put belt on drum and slipped drum onto rollers depressed tension and slipped belt onto motor pulley. Slightly pulled drum up while slipping front panel onto lower catches. Reinstalled top clips and retaining screws. Tested. Closed lid. Done. Much quieter and works fine

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Socket set, Wrench (Adjustable)
Customer: james from auburn, IN

Drum made a thumping sound was really noisey

pulled dryer away from wall took screws out of lint screen lift top removed 2 screws one on each side of front at top and removed front panel. pulled belt off drum removed drum rollers tension pulley and while i was at it pulled back cover off of heating element and blower blew everything out with air hose did a total cleaning installed everything in reverse. i was amazed how fast the parts came the dryer was only down 2 days and it runs like new even if it is 20 years old i highly recommend parts slect and i will use them in the future

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: William from Rocky Mount, VA

Loud rumble and finally the drum stopped because the belt broke

I opened the top and front of the dryer. 1st I pulled out the drum and cleaned up the lint and mess from the busted support roller. Next it was a matter of looking at the enclosed drawing and instructions. I could not believe it was that easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Kevin from White Haven, PA

Making all types of squealing noises

I changed the belt, tension pully and rollers. Runs like new now. I also took the opportunity to clean it out real good while I had it apart.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 5 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Mary from SCHENECTADY, NY

Broken dryer belt

Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and old belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 5 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: JENNIE from NORTH ROYALTON, OH

Drum quit turning due to broken belt

Followed the included instructions in the Maintenance kit. Very easy to understand & follow. Only advice is to have an extra set of hands to assist in re-installing drum w/ the new belt. Entire disassembly & reassembly could be done w/ basic hand tools but went alot quicker using a cordless drill w/ a set of nut/screw driver bits.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 5 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Customer: JOHN from PUNTA GORDA, FL

Will not tumber

I use the manentance kit that was not the problem. I end buying the drive motor and that was it. I was happy with the service I got from part select, overnight mail what more could I ask for? I am also glad I replace everthing with mainentance kit. Thank you for your help john degnan

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 5 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: Todd from Oneida, NY

Sqeaking belt drum wouldn't turn

Unpluged Dryer
Removed the two screws by the lint screen
Lifted the top of the dryer up by using a putty knife to push in the locking clips that hold the top down
unhooked door wiring switch
Removed the front door panel
Removed drum
Shop vac the unit
replaced the worn parts
reassembled the unit

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: vincent from staten island, NY

Broken belt and idler pully

Thanks to the sep by step instructions I got from part select this repair was very simple. The disassembling was relatively easy, my new maintainance kit came the nest day, the machine was already apart and the parts went in without a hitch. THANKYOU

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Bradford from Marseilles, IL

Drum would not turn. Belt and pully were broke.

I watched the video on the websit and it told me and showed me just what to do. Exccelent video, Ordered the repair kit, got it in two days. Job took me about 10 min.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 6 people found this instruction helpful

Parts Used:
  • Maintenance Kit
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: diane from Miami, FL

Clothes dryer got hot, but stopped spinning

got my daughter's boyfriend over.. he is like McEiver.. can fix anything with a bobbypin.... he told me what to order, you delivered it in 2 days.. and the dryer was fixed the next day. All it cost me was a roast beef dinner
Much better than that repairman who would have charged a minimum of $100 plus parts... at probably triple your cost...

Help other customers find the most helpful instructions.

Were these instructions helpful?