Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS373087
NOTE: This kit is for 29" wide dryers built 1965 or later. Please verify model # before ordering as may not work for all models.
This kit comes with one multi-rib belt, two drum support rollers, one idler pulley, four tri-rings, and one clip. This part can be used with both gas and electric dryers.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
This dryer drum belt has four ridges, three grooves and is 1/4" wide.
These two drum support rollers are no longer available for individual sale. Available in a package of two and it is recommended that you replace both rollers at once. These two rollers come with four tri-rings and one palnut.
This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.
Grow a second set of hands. Always unplug any appliance. Remove lint screen. remove two screws (philips Head). I took a wooden shim lightly tapped w/hammer to pop front of dryer top free. Mine worked on hinges and just flipped back til it rested against the wall. Removed two 5/16 screws inside holding face on carefully raise face section off the support clips at either side on the bottom. Pull drum out (I have the large style drum commercial size [approx.). Clean the inside free of all lint (known to be fire hazard). Sling new belt around drum. Get newly grown set of hands to hold drum in place. Pinch belt to fit between tensioner, lift tensioner and place belt around motor pulley. Spin drum couple times to make certain belt isn't twisted. Reverse dismantle proccess to put back together. Replace all parts that come with kit, you'll feel better knowing you got a new dryer, almost.
Help other customers find the most helpful instructions.
Were these instructions helpful?
1st Unpluged power.2nd removed two screws under lint screen cover.3rd poped up lid with flathead screwdryer, then removed (2) 5/16 screws from door cover and unpluged lid switch, lifted up dryer door pannel4th removed drum5th took out plastic triangle wheel rings6th removed old belt guild (to motor pully)7th removed old wheels and plastic rings stops8th cleaned excessive hair dust with shopvac9th put new replaicment part in dryer. made sure to turn manually to make sure belt was lined up properly, then put all dryer peices back.10th aditional work, took back cover off and removed the (4) 1/4 screws for lint screen case (left side in dryer) vacumed out any excessive dirt lint ect, also cleaned any excessive dust I found in back of dryer, dryer , exhaust ect, and put all back together.JUst like a new dryer aain after all PM was complete.
Removed front panel, drum,replaced belt,tensioner and worn rollers. Then removed rear panel and replaced heating element and high limit thermostat. While I was there completely cleaned inside of dryer. Repair and replacement of parts was quite easy. Just take your time and don't hurry it.
Great! Spent about $36.00 and I ended up with a overhauled dryer. I ended up cleaning the whole thing out, it's amazing how much stuff accummulates in the frame of a dryer, I also found about $2.00 in change. It's a good idea to clean out a dryer every few years and the broken belt forced me to do it. But anyway the parts cam very quick and had easy to follow directions. I would reccomend part select. Matt
Pryed the top off the dryer, unplugged the door switch, took the screws out of the front panel, then lifted the drum out. Placed the new belt around the drum and while my wife held it in place and steadied it, I reached underneath and looped the belt through (as per instructions), reassembled and back in business! Reaching under the drum was not that easy....VERY tight space to work in and there was no way I could get both hands through, I almost gave up, but one last try and a couple of good grunts, and it popped into place. Getting the wires back on the door switch was a bit of an ordeal too. Took about 30 mins. but still worth it. I'm sure I saved at least a $100 repair.
super fast shipping, got the part in two days, and had it done in 15-20 min, remove the front pannel, remove the belt and tenssioner,took the drum out , took the old rollers , lubed the shafts,replaced the old rollers with the new ones, intalled the drum back, the tenssioner and the new belt, reinstalled the front pannel, and done...easy and fast job, like new dryer, works nice...save some money...the new one will do the same..just dry the clothes.
It was really quite esy remove the screws from the back and pop the top off . then remove 2 top inside screws from the front , lift the front off the sides , support the drum and lift out , you will then see the idler wheels, replace them with the new ones ,replce the tensioner , wrap the belt around the drum, need help putting the drum back in the case, have someone hold the drum in place while you lay on the ground and put the belt around the motor pulley and the tensioner on the bottom.you then put the front panel back into place and secure with the 2 inside screws, then put the rest back together in reverse oder. ... hope this helps someone
Replaced the belt and the wheels supplied with the kit. I also cleaned the inside of the unit. It looks and works like new.
Took off the top and front panel. Found that the belt tensioner was worn out. Decided to pull drum out,and replace the belt and drum rollers also. Put it back together, and it works fine.
First, I watched a utube video of replacing the dryer belt. Then I went to Sears Hardware and couldn't find a part. Then I ordered the parts for my favorite online repair parts source - partselect.com. I had the part in one day! We did exactly what the video showed and also replaced the two wheels that looked like roller blade wheels. Piece of cake. Saved a $75 repair call plus whatever the parts would have been and spent about 20 minutes doing it. Back in business. Great for a 12 year old dryer! Buy the dryer kit!
I looked for squeaky dryer within parts select and went with the 80%. I received the Maintenance Kit, replaced two rollers and it works like new. Amazing since this is the first time I have ever opened a dryer. The instruction sheet and parts were all I needed.
I took the dryer apart ( using a repair book ) It was Super Simple to do I only needed a extra set of hand's to hold the drum in place while reassembling it. removed the hold down snap on collar's on the Motor ( after removing the Blower from the back of the dryer ( super simple. Extra set of hand's needed ) Reassembled in the same order. And now The Dryer work's like NEW..Shure Beat Buying a new Dryer..
I raised the top of the dryer, removed the front, the belt and the drum. Slipped off old rollers, installed new ones and new tensioner. Reinstalled drum and belt, bolted front back on and closed the top.
Just follow the instructions the one was provided with Maitanace kit we bought from you.
Removed the two screws under the lint trapOpened the top (had to use flathead screwdriver to release latches)Disconnected door switch harness from front panelRemoved 2 screws holding front panel on dryerLifted out dryer drum (previous belt had broken)Vacuumed inside of dryer (found $3 in quarters!)Put new belt around drumPut drum back in dryer, using empty laundry soap bottle to support its weightLooped belt around pulley and motor; secured pulley to dryer bottomMade sure rear gasket thingy was aligned properly and drum turned freelyPut front panel back onRe-attached door switchClosed top and put screws back in under lint trapFired it up - WOOHOO!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.