Quick Question!

Have you ever purchased from PartSelect.com before?

373025-1-S-Whirlpool-4391996           -Flat Style Igniter
373025-1-S-Whirlpool-4391996           -Flat Style Igniter 373025-2-S-Whirlpool-4391996           -Flat Style Igniter 373025-3-S-Whirlpool-4391996           -Flat Style Igniter http://www.partselect.com/Schematics/Maytag/MA38C13.gif

Flat Style Igniter

PartSelect Number PS373025

This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, KENMORE®, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Will Not Start.
  • Takes too long to dry.

Compare At

$35.23

You Save

$5.87

Your Price

$29.36
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 59 reviews What's this?
46-59 of 59
 

0 of 1 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Tereasa from Allendale, NJ

Dryer not heating up

Using your site to review interior parts and similar problems, I determined the issue was one of 3 parts, the igniter, the gas coil or the heating drum. The igniter information was the most consistent since I had NO heat. My plan was to start with the igniter replacement and continue from see what happened. I disconnected the electric, (no need to shut off gas), removed the front panel of the dryer, and replaced the igniter. It took 5 minutes. NOTE that the filament part of the igniter is fragile and must be handled with care. It can break and fall away with little pressure. I learned that the hard way.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Screw drivers, Socket set, Wrench set
Customer: Jerome from Littleton, CO

Igniter quit working

Remove the front panel of the dryer using appropriate tools. Unplug wires to light. Take care to remember how it was dissemble. A good time to remove the vent catcher and clean it out. Remove the one screw on the igniter and replace igniter. Test to make sure it is working before putting the front panel back on.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Wrench set
Customer: Jack from lake orion, MI

Dryer would not light

Took two screws off loser front of dryer. Removed screw that holds in igniter switch, disconnected the two leads. Replaced with new one and that was it, simple. Anyone can do this with little experience.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Socket set
Customer: Rigoberto from Rolling Meadows, IL

Dryer would not heat.

I checked to see if the fire of the gas dryer would start, but nothing. Changed the ignitor coil with kit, used the same socket screw, unplugged the cable and removed old ignitor. New one was placed in and reconnected and finished in less than 5 mins.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 4 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Wrench set
Customer: Jeffrey from Dallas, TX

Gas dryer was not heating up

I removed the front panel from the dryer and observed that the glow plug was not getting hot when the dryer was turned on. I removed the glow plug and verified that power was present using an OHM meter. Power was present. I could also see a hairline crack in the glow plug. The new glow plug took about 2 minutes to install and immediately glows red when the dryer is turned on. Easy fix.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Socket set
Customer: Juan from San Pablo, CA

Gas dryers stop heating

Per instruction found in the internet about the simptoms and recomended parts wich ussualy goes bad in that model I follow the intructions of a tecnitian to replace the igniter and the termal fuse.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Anton from Monroe, NY

Dryer was not drying clothes

I went to a repair website to see what some of the problems could be and tested for them. I checked the power starting at the circuit breaker box and went all the way to the igniter. I discovered that the igniter had a small break in it and determined that that was the cause for dryer heat not coming on.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 4 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Lance from Ventura, CA

Dryer spins but doesn't heat

Replaced igniter.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Raymond from Johnstown, PA

Gas dryer would not heat up

I checked the sensor and other components for continuity and found they all worked ok. I check the Igniter and found no continuity or resistance. That was the problem. Installation was easy. One screw and a two wire plug.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Annamarie from Crestwood, IL

Igniter went out on dyer

my husband took the old igniter out and put the new one in and it was fix. your websit was very easy and very resonable price. thank for your help

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: DARREN from GREENSBURG, IN

Dryer would not heat up.

Removed the front cover of the dryer. Unpluged the igniter and then removed srcrew and replaced with new igniter.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: LAWRENCE from MARINE ON ST CROIX, MN

Dryer will not heat

Removed the front of dryer and replaced igniter, old igniter was in bad shape, but it did not fix problem. Looks as if I need to replace gas valve assembly also.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Wrench set
Customer: Stephen J. from Flint, MI

Dryer not heating

It took me about 20 minutes to figure out how to remove the front cover, and 10 minutes to remove and replace the ignitor. Works like a charm. Saved me lots of money. $$$$$$$$$. Thanks for the information.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Flat Style Igniter
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Miro from flushing, New york, NY

Igniter broken

ordered and replaced igniter. problem fixed

Help other customers find the most helpful instructions.

Were these instructions helpful?   

46-59 of 59