Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS372186
This white ice bin auger drum comes with a washer.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Removed Ice bin from FridgeRemoved all bolts on bin with nut driver...about sixRemoved housing...be careful with spring on crusher/cube control rodRemoved C clamp on end of auger with small slotted screw driver and needle nose pliers.Removed plastic nut on end of auger shaftRemoved Ice crusher jaws and laid them out in the correct orderRemoved Ice propeller and installed new partPut back together in opposite orderEasy
Help other customers find the most helpful instructions.
Were these instructions helpful?
The repair was actually easy; however I have an ice dispencer/crusher attached and the which the diagram supplied with the part did not include. I had to make several calls before I was e-mailed the diagram. Suggestions: note that the screw at the end of the auger goes in the reverse direction (this took me about 20 minutes to figure out even though it was shown in the diagram). Also, be sure to keep the ice crusher parts in order and be sure the white plastic tab on the crusher fits into a depression in the housing. I did not notice this and had to take it all apart and redo the install. It works great!!!
Initially I removed the cover to the auger and auger drum. Then the split ring locking washer had to be removed. I used a needle-nosed pliers and small screw-driver to pry that off. The auger arm could then be removed, and the auger blades removed. This proved to be the part that required the most patience. The blades need to removed and returned in their exact pattern. Someone else suggested taking a digital picture of them before removing them; this is a good suggestion that I failed to do. Once the blades are returned, all the other parts can be replaced in reverse order. Put the screws back in, and you are finished.
Be advised that to do this job, you have to take the ice tray and feeder assembly completely apart. The only tricky part is that the nut, part 31 in the drawing, that holds everything together is reverse threaded. Since it's plastic, you're afraid you'll break it. If you know it's reverse threaded to begin with you can go ahead and apply the required force to get it off.
After removing a few screws to get to the drum my husband had it back to working like a charm.This part seems to be better made than the original part in the refrigerator.
Removed ice bin then pulled front cover with nut driver . Pull small rod from side ( one screw holding rod and spring). Pull auger out. Take plastic nut off end ( CLOCKWISE) LEFT HAND THREAD. Keep all ice crusher blades in order when you pull them off. Install new auger and reverse steps. web site has exploded view. It looks difficult but it isn't.
Replaced the ice bucket (old one was cracked) the auger, auger coupling and auger drum. The new parts had been redesigned to replace the orginal auger helix and auger sleeve which had been replace two times and never seemed to last more than a few weeks. The new parts work great and we have as much ice available as we need. The replacement was stright forward but I do reccomend that you make a simple drawing of the ice crusher blade and washer locations as you dissassemble them to aid in reassembly.
I looked up the PartSelection website. Found the parts from the sketches of units and reviewed the videos on repairs. Then I ordered the parts, altho I ordered the complete unit, instead of the control block that said was problem 59% of time. Following instructions replaced the ice maker. Then took apart the auger in the basket and thought I had an incomplete part, but upon closer inspection forund out it was correct. My only problem was that there was no instructions on how to get the block off end of shaft. Tried to impact it off, but by accident found out it screwed off. Then final repair went fast. Parts came fast and overall VERY happy with parts and repairs. They are heavier than original parts so should last longer.
Removed ice bucket and discovered the auger drum was broken. After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.Works great now, crushed and cubed ice dispenses thru the door like new.
I removed the screws that attached the drum housing to the bin. I detached the auger & removed the broken drum assembly, turning the auger to the right, opposite what I thought it should be. I slipped the end of the auger into the new bin coupler & put it in place at the rear of the bin. Next I slipped the auger drum into place & tightened it to the left with a socket wrench. I screwed the drum housing to the bin, put the bin back into the freezer & I now have ice through the door again. Easy repair even for me, a 60+ woman.
Pulled out the ice bin and dumpted ice in the sink. Use 1/4 inch nut driver to take out all 1/2 inch screws. Be careful to watch how door spring and holder goes. Pull assembly apart and remove alger. Plastic nut on end of alger has reverse threads, remove it and then remove broken alger drum. Replace with new drum and reassemble in reverse order.
took out old ice maker (3) screws unpluged power plugged new one in replaced screws , installed new icemaker shut off arm and done Ice bin auger disassembled bin to get at auger drum replaced broken auger reassembled bin and done 30 min tops hardest part was figuring out how to get bin apart
I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me. I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!The PartSelect service is great!
Removed all ice from bin and let it thaw. Removed all screws and nuts from the front to release the ice crusher and the long bit. Had already printed out all the advice from others on the on-line section about taking photos and not getting the crusher blades out of order. Removed the clip with needle nose pliers and the washer. Removed the blades laying them down in exact order and direction they came off. Put on the new auger drum and reversed everything. It was nice to know that the plastic screw that held the clip is a reverse thread, otherwise we might have broken the dang thing. Too bad there aren't instructions with the part when you get it instead of just a diagram. All-in-all, it went well.
1. Pull out drawer. 2. Remove screws to release the auger. 3. Unscrew the end of the auger. 4. Pull parts off. 5. Replace drum. 6. Replace parts in the correct order. 7. Twist end of auger back on. 8. Replace unit onto drawer and install mounting screws. 9. Place drawer in freezer. 10. Test ice dispenser. 11. Watch kitten run to refrigerator and beg for ice cube. 12. See smiles on family members faces.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.