Nozzle and Tube Kit

PartSelect Number PS371704

This kit is intended for use with refrigerators that have a water dispenser in the door.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Not dispensing water.
  • Compare At

    $60.14
  • You Save

    $10.02
  • Your Price

    $50.12
In Stock
Order within the next 6 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 17 reviews What's this?
1-5 of 17
 

41 of 53 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRobert from Abingdon, MD

Water dispenser tube broke

To put the new tube in, I cut the old tube before the Y piece(screw to door part) and taped the new hose to it. I pulled the old tube from the bottom of the door, while gently pushing/feeding the new hose in until the new hose was at the bottom of the door. Connected the new hose(top/bottom) and turned the water back on. All of 7 minutes.
Thanks for the fast service...

Help other customers find the most helpful instructions.

Were these instructions helpful?

26 of 29 people found this instruction helpful

Parts Used

  • Nozzle and Tube Kit

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerRobert from Tuckerton, NJ

Nozzle was broken

Didn't know if part was replaced from the front or back of door. Removed back/inside first. Good excuse to clean mold found in places not normally seen. The only real problem was getting the face off the dispenser without breaking it. I now know it snaps off from the bottom. To replace one little nozzle you have to replace about 10' of tube. When I pulled the old tube out. I attached fishing line to it and used to fishing line to help feed the new tube through the door.

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 22 people found this instruction helpful

Parts Used

  • Nozzle and Tube Kit

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsPliers, Wrench set

Customerhaig from La Quinta, CA

In door water dispenser tube broken off 1.5 inches from end

shut off water supply behind fridge then released trapped water pressure in the line at the dispenser. Locked off dispenser controls (push button switch). Removed nozzle retaining screw and pulled out nozzle approx. 3 in. to cut off tubing at black pipe so as to use the old pipe as a guide/pull (fish) for the new pipe by joining the end of the new nozzle to the cut and of the old pipe with electrical tape.Then pulled the old pipe from bottom of fridge while simultaneously feeding/pushing new pipe from top. I had to remove lower grate on fridge to access the pipe on bottom. Remaining coupling connection on bottom was done by hand to avoid stripping plastic coupling.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 17 people found this instruction helpful

Parts Used

  • Nozzle and Tube Kit

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsWrench set

CustomerDave from Danville, AL

Water leaked on floor when water dispenser was used.

1. Turn off water supply to refrigerator.
2. Unscrew water nozzle from dispenser.
3. Remove grill on bottom front of refrigerator.
4. Unscrew tubing at the left side of the union.
5. Unclip tubing from the refrigerator frame.
6. Pull tubing out of the dispenser about 6 inches.
7. Cut off nozzle with scissors.
8. Insert 1/4" diameter x 1" long molly bolt about halfway into end of tubing where it was cut.
9. Insert the remainder of the molly bolt into the end of the new tubing.
10. Pull the old tubing through the bottom of the door.
11. When the new tubing is pulled all the way through the door disconnect from the old tubing. Remove molly bolt if it is in the new tubing.
12. Remove the ferrel from the old tubing and use to attach new tubing to the union.
13. Connect the water nozzle to the dispenser.
14. Insert new tubing into the clips on the refrigerator frame.
15. Re-install grill.
16. Turn on water.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 16 people found this instruction helpful

Parts Used

  • Nozzle and Tube Kit

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerMichael from Colorado Springs, CO

Plastic water spout broke off

Turn off water supply line fridge. Removing front panel is a must to allow acces to spout and water line. Be careful not to crack front panel $90, it snaps in from the botton, slide a stiff putty knife along bottom edge and gently pry outward to remove. Remove 2 screws that hold spout in place, then cut water line right behind spout. The tricky part is fishing water line down through door. You need to splice new line to old with double sided screw or something with threads that will prevent the lines from pulling apart, then pull water line from bottom of door by hinge, very tight when pulling through hinge opening. You will need to remove vented dust cover at botton of doors to acces the water line. The line has a threaded coupling so unscrew and drain water then cut new line to length. There is a small metal insert in old line that needs to be removed and inserted into new line before attaching coupler. I could perform this in half the time now that I have done it once.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 17