Nozzle and Tube Kit

PartSelect Number PS371704

This kit is intended for use with refrigerators that have a water dispenser in the door.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Not dispensing water.
  • Compare At

    $60.14
  • You Save

    $10.02
  • Your Price

    $50.12
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 17 reviews What's this?
 

13 of 14 people found this instruction helpful

Parts Used

  • Nozzle and Tube Kit

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers

CustomerCatherine from Mount Pleasant, SC

Plastic nozzle that dispenses water broke off

the parts sent included two replacement kits which at first was confusing. I determined that I only needed the one with the black tubing for my Kenmore refrig. Turned off water supply and vacuumed up all the dust bunnys behind refrig. Removed bottom grate on refrig where black tubing attaches at the other end. Released water left in tubing at dispenser. I did not have to remove the front panel. Removed one screw attaching the nozzle to the dispenser. Decoupled tubing at the far end, more water came out here too. Pulled out upper end of tubing a couple of inches and snipped off. Attached tubing to new tubing with thin wire (as others here recommended) and had my husband pull at far end while I pushed slowly at the dispenser end. Once through reattached screw at top and recoupled at the bottom. Mission accomplished!

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 11 people found this instruction helpful

Parts Used

  • Nozzle and Tube Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerTom from Roseville, CA

Nozzle on water dispenser broke off.

First, turn of the water supply. Then remove the snap on grill from the bottom front of the refrigerator. Disconnect the black hose from the white hose and drain the hoses into a suitable recepticle. Then remove the 1/4" screw that holds the nozzle in place. Cut the hose off just behind the nozzle bracket and tape the end of the new hose to the now exposed end of the existing hose. From the bottom of the door you can now gently pull out the old hose while pulling in the new one. Re-attach the new hose to the existing white hose and replace the 1/4' screw to the new nozzle bracket. I reccoment using 1" wide tape and only going around the tubes once. Too much tape and you won't be able to feed it through the small hole at the bottom of the door. Have someone feed the hose from the top as you gently pull from the bottom.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 12 people found this instruction helpful

Parts Used

  • Nozzle and Tube Kit

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers

Customerthomas from corona, CA

Broken water dispenser spout

part arrived within 24 hours.
1. remove plastic front of freezer door water and ice dispenser by looking at bottom edge of plastic for two slots within which to place a stiff scraper blade. very difficult to pop loose and very fragile plastic so take care not to break it. it just pops off two spots on the bottom side and hangs from the top no screws or anything.
2. remove the two screws holding the water dispenser spout in place. oh yeah don't forget to turn the water off.
3. this is a long plastic water tube that runs from the dispenser thru a plastic tube channel set in the solid foam core of the door thru the bottom hinge and connects to the water inlet junction.
a. this replacement must be pulled from the dispenser area thru the door and out the bottom but it will not fit without cutting off the end of the spout. the hole in the hinge that it passes thru at the bottom of the door is to tight to allow anything other than the thickness of the tubing.
b. pull the spout end of the tubing upward after disconnecting at the bottom in front behind the air grill. if it moves freely you are in luck - if it does not move freely then it is taped in place on the back of the dispenser area and now that whole assembly has to be unscrewed from the front of the freezer door in order to remove the tape so that the tubing can be pulled thru.
4. once the tubing pulls easily as short distance in either direction it is time to attach the new tubing to the old tubing and pull it out the bottom of the door. i tried to use tape but it pulled off when i got to the door hinge on the bottom and it would not fit thru the hinge.
a. on my model even one layer of tape would not fit thru the hinge. so i put some bricks under the freezer door to hold it up and removed the bottom hinge off of the tubing that was disconnected only a short distance away.
5. use tape or place a screw with the head removed into both the old tubing and the new tubing so it can be pulled from the bottom moving the new tubing into place.
mine broke off in the middle of this process and i had to remove the freezer door. take it completely apart to expose the conduit the tubing slides thru, then run an electrical fish tape thru the conduit and drag the new tubing thru, not a fun process but doable - just takes a bunch of extra time.
6. once the tubing was out the bottom i could then simply thread it thru the hinge easily and reassemble everything.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

  • Nozzle and Tube Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJIM from SACRAMENTO, CA

Spout on water dispenser broken

Cut off old nozzle. Tried electricians tape to join the old and new tubing for fishing, but tube with tape on it, wouldn't fit through hole in hinge at bottom of door. Fished nylon twine through new tube then old tube from dispenser end and was able to feed old tube out and new tube in. Fast and easy. Took more time to clean all the dust and dirt I found down under, than to make the repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Nozzle and Tube Kit

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerRobert G. from Kalkaska, MI

Tube got cut and it leaked

first I turned off the water supply then I removed screw that was holding the nozzle and pulled out the tube then I pried out the face plate by prying from the bottom with a thin screw driver then I unpluged the wire harness so I could access the black tube guide that the white tube was housed in before it was cut I pushed the new white tube down threw the black tube and out the bottom hinge I replaced the nozzle screw plugged the harness back in replaced the face plate went to the bottom and connected the tube to the other half replaced the bottom molding and turned on the water

Help other customers find the most helpful instructions.

Were these instructions helpful?