Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Mark M - December 30, 2023
Verified Purchase
Easy to install and the part was made of quality materials.
The part was just like the original
★★★★★
★★★★★
Karen C - June 16, 2018
Verified Purchase
Very easy to replace
Part is exactly what was needed. Easy to replace the rollers. Works very well
★★★★★
★★★★★
Dennis S - May 15, 2018
Verified Purchase
Easy Repair --
Great to have a source for parts
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.3 / 5.0, 8 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
One of the front wheels was broken in half.
Very easy. Left the front of the refrigerator so it is approx. 4 inches of the floor. (used a two by four. Removed the screws (one for each roller). Removed the rollers and replaced with new rollers. Reinstalled the screws with secures the rollers to the refrigerator. Done
John from INNSBROOK, MO
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken wheel under fridge
Replaced both since they came as a set. The only way it could have been any easier is if I had the wife do it. She had the remote this time. (•¿•)
Ted from Magnolia, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Compressor making excessive noise
One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled
... Read more the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!
Both front wheels were severly damaged needing replacement.
I tipped the refrigerator back and my friend used an adjustable wrench to attach put the new wheel assembies on. I also used a socket wrench to get the old attacheement bolts to thread. I rolled the cleaned appliance in place and adjusted the wheels with the socket set for easy door closing. It went smoothly.
James from Leesburg, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set, Wrench (Adjustable)
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front wheel was broken when moving refrigerator
Lifted the front up onto a scrap 2x4 to get it off the ground and it had 1 bolt that you removed to get the old item off and replace with new assymbly and 1 bolt to re attach. This sat broke for over a year becuase I thought it would be alot harder to fix, found the part on parts select ordered it recieved it in approx 2 days and had it f
... Read moreixed in less than 15 minutes. I would recommend parts select to anyone who told me that they had a appliance broken. Thanks
First I had to tilt the refrigerator on wood on the supports under the refrigerator, the wheels were easy to get to then I unscrewed the old ones and replaced them with the new better wheels. The old ones where plastic.
Mary from Pelham, NY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken wheel on leveling roller
I removed one bolt and took out the old roller after first blocking up the fridge. Then I was puzzled for a moment because the hole in the new assembly was not tapped. But then I saw that the old bolt was a self tapping bolt. I used it to tap the hole then removed it and installed the new assembly. No sweat job.
Max from Jonesboro, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
2 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken front roller set and a snapped shelf support.
While moving our refrigerator when remodeling the kitchen, the front roller assembly shattered from age. The original set was made of nylon and age made it very fragile. Also to make the move easier, we removed the shelves. In the process the lower shelf support stud snapped.
When the parts came the first thing repaired was th
... Read moree shelve support stud. Very easy job to do, just take the pliers and rotate the broken stud counterclockwise a quarter turn and remove. Put new stud in the hole in the same position as the removed stud and gently, but firmly rotate the stud a quarter turn clockwise until it seats.
The front roller assembly requires a socket set, block of wood about 1/2 - 1" thick flashlight and 4’ level. First, remove the front grill by opening both doors of the side by side and pulling the grill out of its left and right side anchors. Close the doors. Place the block of wood under the front support near the center. Remove the leveling screw from the old assembly and install it loosely in the new assembly as the new assembly has no leveling screw. This will now allow you to remove the old assembly by removing the remaining screw in the roller assembly on the front refrigerator support and turning the roller assembly slightly counterclockwise and pulling out the front. You may have to wiggle it, as it sits in a slot on the side support of the refrigerator. To install, place the new assembly in the same position as the old, locate the slot with the flashlight and push the roller set tab into the slot. Attach the support screw and tighten while holding the assembly in place. It is a good idea to replace both rollers at the same time. The same rollers will fit both sides. Now level the refrigerator by tightening the leveling screw until the front rollers now touch the floor. Next, place the level on the top of the refrigerator diagonally but not on top of the door supports. Turn the leveling screws until the bubble is in the center when the level is set in either diagonal position. Replace grill and you done.
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Hazel
March 28, 2019
Do the front wheels lock somehow? When we open the door the whole fridge rolls forward.
For model number 106.5175
Hi Hazel,
Thank you for your question. There are no brakes for the rollers. If it is rolling forwards when you open the door, the refrigerator is likely not level and you will need to check and level it. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Joseph
February 25, 2022
Regarding part #PS370711 which is the correct part for my front rollers though most list a different item…. I am looking for bolt/screw that goes into bottom hole (attaching it to refrigerator). Not sure the one in diagram is correct since it shows different roller
For model number ED5LVAXWS01
Hello Joseph, thank you for writing. The front roller is PS11738962. The screw that goes into bottom hole is PS11742746. We hope this helps.
i need both front and rear wheels. Front wheel kit indicates two wheels come in the purchase. The rear wheels appear to be sold individually, Is this correct? Do I need to order two?
For model number KSRL25SRSS00
Hello Donald, Thank you for your inquiry. We have researched the model number you have provided and confirm that the rear rollers are sold individually and you would need to order two. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
I need to replace both front and rear wheels. The product page for the front wheels specifies they come in a kit of 2. I don't see any similar specification for the rear wheels. Do the rear wheels also come in a kit of 2, or are they sold singly?
For model number KSRL25FRSS00
Hello Don, Thank you for your inquiry. The specifications of the rear wheels listed under the part description state that they are sold individually. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
