3655072-1-S-Frigidaire-154860103-Detergent Dispenser
3655072-1-S-Frigidaire-154860103-Detergent Dispenser 3655072-2-S-Frigidaire-154860103-Detergent Dispenser

Detergent Dispenser

PartSelect Number PS3655072

This part releases the detergent and rinse aid into the dishwasher.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Will not dispense detergent.
  • Door latch failure.
  • Compare At

    $72.49
  • You Save

    $12.08
  • Your Price

    $60.41
In Stock
Order within the next 7 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 4 reviews What's this?
1-4 of 4
 

13 of 19 people found this instruction helpful

Parts Used

  • Detergent Dispenser

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerC from Covina CA

Dispenser door broken.

Disconnect from power
Unscrewed 4 phillips screws from top of outer door.
Unscrewed 2 screws each siide of door.
Lower outer door section drops away.
Note wiring sequence on dispenser, then disconnect wires.
Unscrew 6 screws on dispenser and lift dispenser out.

Place new dispenser in place (note orientation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw.
Reconnect wires to dispenser correctly.
Slide lower outer door over tabs and secure with the 4 side screws.
Ensure lower door is up under control panel and secure with the 4 top screws.

Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done..

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Detergent Dispenser

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJustin from Miami FL

Broken door on dispenser

The only difficultpart was to figure out how to remove the stainless cover from the door. Seems it slides upwards after screws are removed. After that it is self explainatory and goes back together in 5 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Detergent Dispenser

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerStephanie from Fort Wayne IN

Dispenser door latch broke

removed the screws holding the door together, then removed the screws holding the dispenser to the interior door. replaced the wires and put the door back together

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 12 people found this instruction helpful

Parts Used

  • Detergent Dispenser

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerPaul from Lorton VA

Rinse aid dispenser leaking and empty after 4 wash cycles

Needed to replace detergent / rinse aid dispenser unit on the inside top of door.

1) Need to remove outer door cover / panel by removing just two (2) screws - bottom screws on lower side panel. Door panel will drop vertically 1" to remove it.

2) Mark and disconnect the four (4) wires connected to the dispenser unit. The connections were so tight, it required pliers and a screw driver to loosen them.

3) Dispenser unit has four (4) screws holding it in place. Unscrew them and remove unit through door interior - this requires a bit of angling to get it out.

4) Position new unit through interior. Screw in place.

5) Re-attach four (4) wires in same sequence as disconnected.

6) Re-attach outer door cover. This is the most difficult part and really requires two people. It consistents of two sets of guide channels that most be aligned for the door panel to be secured re-attached.. Once aligned, the door cover must be moved vertically about an 1" and the screws re-attached.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4