3654822-1-S-Whirlpool-W10454648-Light Socket
3654822-1-S-Whirlpool-W10454648-Light Socket 3654822-2-S-Whirlpool-W10454648-Light Socket 3654822-3-S-Whirlpool-W10454648-Light Socket http://www.partselect.com/Schematics/Maytag/HSDIUUU9.gif

Light Socket

PartSelect Number PS3654822

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $37.54
  • You Save

    $6.26
  • Your Price

    $31.28
In Stock
Order within the next 10 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 9 reviews What's this?
1-5 of 9
 

29 of 39 people found this instruction helpful

Parts Used:
  • Light Socket
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Edmund from Emporium, PA

Socket light had a bad thread

Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cover

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 20 people found this instruction helpful

Parts Used:
  • Light Socket
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Lewis from Chapin, SC

Inside brass liner in socket came out when bulb was removed. Apparently had welded itself to the base of the bulb

Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 21 people found this instruction helpful

Parts Used:
  • Light Socket
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools:
Customer: Carol from Allison Park, PA

Oven light not working

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: LOUIS from FREEPORT, TX

Oven light would not work, old bulb broken

Had already removed back covers and disconntedted power. When io received parts I replaced them in reverse oder I had removed them. Took me longer to replace back covers because of my bad diabetic hands. Thanks very much, yopu savbed me a bunch. God bless you and yours, god bless america.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used:
  • Light Socket
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Delores from Warren, MN

Oven light would not work--faulty socket

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 9