| |
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerCraig from St Johns FL
Old handle had broken
inserted on an angle and snapped in place.
The best part of this story was I ordered the part on a Saturday and got it on Monday evening.
The repair took less than 20 seconds. I am extremely impressed with the fast fast fast shipping time.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerGreg from Macon GA
Had be sqeaking like da mickey mouse
First opened cold Bud then pulled screwdriver out of toolbox. Removed all of six screws (quality workmanship of appliance) and put on 6 pieces of plastic (do they make metal any more??????).
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerCraig from Pittsburgh PA
The door handle of our dryer broke off
After removing pieces that were stuck in the door, I simply popped the new handle in place. It took less than a minute. What was the easiest was ordering and receiving the new parts- I ordered and 2 days later I received the new parts. I didn't expect to get the new parts for at least a week.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerKevin from East Peoria IL
Dryer made a squeaking noise while running
I removed several torx srews across the back control panel. Removed two philips screws under top of front dryer door. Pulled up on top surface of dryer case. Removed two more screws on backside of front door panel. Pulled front door panel forward and inserted drum slides into slots that they just popped into with a small button rod to keep them in place. The old drum slides were completely worn down or fell off. It runs like a new one again. It is over 10 years old.
The new door handle just snapped into place.
Original door handle had been broken off for several years.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerMichael from Chesterfield VA
Freezer cold, refrigerator not cooling
First I removed the top shelf and its contents to allow for more room. Then I removed the plastic temperature control housing by tugging housing forward and releasing it from the two clips located at the upper rear corners of the fridge. Then pull down. Then I removed the three screws holding the entire temperature control assembly and dropped it down to access and remove defrost assy. Installed new defrost assy. and re-assemble in reverse. Change light bulbs before replacing final housing. Also, a good time to clean housing interior before re-installing.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMichael from Lumberton NJ
Plastic door handle broke
Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerWilliam from Joliet IL
Pull door handle broke
No tools needed as old handle had come out on it's own when it broke. Simply removed duct tape that was used holding old one in place till new one arrived. Placed new one in position and snapped into place to hold. Less then a minute to install. Very pleased and surprised in how fast delivery of part from PartSelect was. Basically had it in 2 days. Will use them for other replacement parts as the need arises.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJoyce R from Boca Raton FL
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDeborah from Dublin OH
The handle on the dryer broke off
I ordered the new part as listed and it came in two days, which was amazing to me since it was the week before Christmas. I snapped it in in less than a minute and all is well. Thank you for being so prompt on sending this out. Made the holidays a lot easier.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerVicki from Redlands CA
Door handle broke off
Just popped the new door handle on.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMichael from Houghton Lake MI
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerAMY from RICHMOND VA
Dryer door handle broke off
Very satisfied. I simply took the plastic door handle out of the package and snapped it into the door. It popped right in and fit perfectly!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJames from Antelope CA
Handle got broken off 7 years ago and just 3 months ago the start knob cracked in half
I got tired of every one complaning and using one of the knobs from the stove to start the dryer, I found this site and the parts and there you go.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMYLES from FORT SMITH AR
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDavid from Cypress CA
Plastic handle broke off.
Removed door and two screws to replace the door handle. Reassemnled in reverse order. It was a snap.
|