FAN ASSEMBLY,CROSS FLOW ADP67813503
Rated by 1 customer
Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
$
62.51
In Stock
Get FREE EconoShip on orders over $100! T&C apply
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
PartSelect Number PS3639073
Manufacturer Part Number ADP67813503
Manufactured by
LG
Troubleshooting
This part works with the following products:
Air Conditioner.
This part works with the following products:
LG.
Part# ADP67813503 replaces these:
ADP67813501, ADP67813502
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 1 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Broken Cross-flow Blower Fan
This repair was on an LG ductless heat pump. After some period of use, the inside unit will get very dirty inside with moisture, dust, and possibly mold. To clean the insides properly, you will likely have to remove the fan blower wheel. To do this, you will have to disassemble the outside covers of the unit. There are videos on YouTube t
... Read more
hat will give you some insight, but the different brands are all a little different in the way they are put together. However, it is still fairly straightforward to get access to the blower wheel. I removed the large outside cover (2 or 3 screws) and then loosened the drain tray at the bottom (also 2 or 3 screws). I did not take the drain tray off because it has the drain tube attached at the rear, and it appeared that it could be difficult to get this back together. Instead, I just removed the screws and pulled it down away from the blower wheel. I then loosened the coil assembly covering the top and front of the blower wheel (2 screws). Again, I did not try to remove the coil assembly because it has the refrigerant tubing attached. At this point, you can use a Phillips screwdriver to reach through the blower wheel on the right end and loosen the setscrew in the hub holding the blower wheel to the motor shaft. Once the screw is loosened, you can lift the coil assembly away and pull the blower wheel out to clean it. Unfortunately, while I was cleaning and drying the blower wheel (which was almost completely clogged with crud), I dropped it and it broke. I ordered the new part from this site. The part was on backorder, but after I received it, I used the reverse procedure to install the new blower wheel. The one thing that is a little tricky is that the setscrew in the blower wheel hub tightens down on a flat on the motor shaft, so you will have to be careful to get the two lined up as you push the blower wheel on the shaft because it is difficult to align them after the wheel is on the shaft. At this point, all you have to do is tighten the setscrew on the motor shaft and reassemble the unit NOTE: while you have the blower wheel out, you can get fair access to the housing inside the unit to clean it.
Read less
-
Robert from BURTON, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS3639073
Manufacturer Part Number: ADP67813503
Manufacturer Part Number: ADP67813503
Brand
Model Number
Description
Back to Top
FAN ASSEMBLY,CROSS FLOW
$
62.51
In Stock
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.