356311-2-S-Whirlpool-4171544           -Rubber Water Delivery Tube
356311-2-S-Whirlpool-4171544           -Rubber Water Delivery Tube 356311-1-S-Whirlpool-4171544           -Rubber Water Delivery Tube 356311-3-S-Whirlpool-4171544           -Rubber Water Delivery Tube http://www.partselect.com/Schematics/Whirlpool/Whirlpool_Thumb/3XW6Y5QT.gif

Rubber Water Delivery Tube

PartSelect Number PS356311

This rubber tube carries water from the upper spray arm manifold to the receiver of a dishwasher. This thin walled tube can become brittle over time and crack. If it does, it will lead to poor cleaning quality of the dishes on the upper rack, and you will need to replace it.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not cleaning dishes properly.
  • Leaking.
  • Compare At

    $21.73
  • You Save

    $3.62
  • Your Price

    $18.11
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Upper Spray Arm Receiver

Part Number 356334

$27.62
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.8 / 5.0, 93 reviews What's this?
 

8 of 8 people found this instruction helpful

Parts Used

  • Rubber Water Delivery Tube

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerRicka from Houston, TX

Original tube had started splitting --dishes not clean

I read the repair stories. Did not remove anything but the old tube. Used hairdryer to heat one end, pushed it onto front opening; heated other end, pushed it onto back opening. Took 5 minutes. Saved estimated $196 service call, parts,labor. (NOTE--I caution against using petroleum-based products like vasoline -- cause rubber to deteriorate. Hairdryer is the best solution.)
Grannie in Houston TX

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Wrench (Adjustable)

CustomerDAVID from MAPLE GROVE, MN

Dishwasher would only partially fill with water.

First turn off the power and water. Water valve is under the sink. I removed the two lower panels with 5/16 nut driver. I disconnected the valve from the cross member, again with a 5/16 socket. I removed that cross member with the same nut driver. I disconnected the rubber hose using pliers. I unplugged the electrical connector from the valve body. I held the water inlet pipe with a wrench and twisted the valve off with the adjustable pliers. I applied teflon tape to the water inlet pipe and reassembled. Works like new.

For the rubber water tube I pulled off the old tube, put some dish soap on the new tube and it slid right on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerJoyce from Kennesaw, GA

Replaced water feed arm to top dispenser

The parts were to ship on Monday, which they did and they arrived on Wednesday. The job took less than five minutes and it was done by hand. The parts were as described and were exactly what needed to be replaced. It was simple matter of putting the water tube on the spray arm receiver and then attaching them to the upper spray arm. It required only a little working of the parts back and forth, by hand, and then fitting them into place. It was a very simple and inexpensive repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

  • Rubber Water Delivery Tube

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerWarren from Anacortes, WA

Dishes were not getting clean

I removed the clip holding the old tube in place, pulled it off where it was attached to the upper rack hub and removed the cone shaped coupler from the back end of it. Attached the coupler to the new tube, pushed the tube onto the hub and re-attached the clip. Started up the dishwasher after putting in a few glasses into the top rack and they came out clean! Amazing how functional parts make a difference. BTW, the new rubber tube arrived 2 days after I placed my order... very quick service. Thank you very much.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Rubber Water Delivery Tube

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerJulie from Northville, MI

Water tube had holes and was cracking and the rubber was not soft anymore

First I tried duct tape until I could figure out how to get the part. I went online and found that part that I thought it was, but I wasn't sure since the tube I had was very stiff and looked like it had a particular shape on each end..the one on the site was just a straight tube. I removed the old part which was easy, it pretty much fell off and then pushed the new one on and it conformed to the ends needed since the rubber was soft. It was so easy and the machine works really well again!

Help other customers find the most helpful instructions.

Were these instructions helpful?