353483-1-S-Whirlpool-4157180           -Suface Burner Ignition Switch
353483-1-S-Whirlpool-4157180           -Suface Burner Ignition Switch 353483-2-S-Whirlpool-4157180           -Suface Burner Ignition Switch

Suface Burner Ignition Switch

PartSelect Number PS353483

When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not start.
  • Compare At

    $32.95
  • You Save

    $5.49
  • Your Price

    $27.46
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 4 reviews What's this?
1-4 of 4
 

8 of 9 people found this instruction helpful

Parts Used

  • Suface Burner Ignition Switch

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRichard from Lansing MI

Ignitor did not spark when turning the know

Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Suface Burner Ignition Switch

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerJohn from Perth Amboy NJ

Left rear burner would not ignite

Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

  • Suface Burner Ignition Switch

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJoseph from Lake George CO

Right front gas burner ignitor wouldn't spark

I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Suface Burner Ignition Switch

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerWarren from Las Cruces NM

Two burner ignitors would not function on cook stove

1. ordered two new switches
2. installed switches
3. all ignitors work

Really appreciated the pictures of the parts--made selection very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4